Emerald K6+ is an Emerald engine-management designation. Six injection and six ignition drivers; three speed triggers; TPS and/or MAP load; CAN 2.0B; triple map switching. The generic unit is supplied with starting maps and configurations that still require engine-specific setup. Emerald manufacturer information.

Identification and configuration
Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.
Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.
Pinout, harness and software
Use the K6/K6+ documentation and the actual configuration in the manufacturer's manuals index. A DBW part-loom wiring diagram applies only to its stated configuration. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.
See Emerald adapter catalogue and Emerald standalone ECU overview.
36-way manufacturer DBW part-loom example
Emerald’s K6 part-loom schedule for drive-by-wire with inductive crank and cam sensors identifies every connector cavity, viewed from the cable-entry side. This is a specific DBW loom configuration, not an assurance that every K6/K6+ hardware revision or loom uses identical assignments. Match the ECU configuration and serial number with Emerald. The manufacturer sheet includes an older hardware-v1.40 example; verify its applicability before wiring a particular unit.
| Pin | Example wire colour | Documented function |
|---|---|---|
| 1 | Yellow/black | Injector driver 4 / AuxOut1 |
| 2 | Orange/blue | IACV2; DBW motor (+) |
| 3 | Orange/green | IACV1; DBW motor (−) |
| 4 | Green/yellow | Ignition driver 3 or main relay |
| 5 | Green/black | Ignition driver 2 / AuxOut5 |
| 6 | Blue/yellow | Cooling fan relay |
| 7 | White/pink | Throttle position signal B |
| 8 | Green | Throttle position signal A |
| 9 | Red | +5 V sensor supply (100 mA maximum) |
| 10 | White/yellow | AuxIn10; configurable internal pull-up |
| 11 | Red/black | Ignition sense input (+12 V switched) |
| 12 | Yellow | Tacho output |
| 13 | White/green | Immobiliser / auxiliary digital input |
| 14 | Blue/red | AuxIn14 / AuxOut14 |
| 15 | Red | Cam sync signal |
| 16 | White | Air temperature signal |
| 17 | Yellow/pink | Injector driver 5 / AuxOut17 |
| 18 | White/black | Oxygen sensor signal earth |
| 19 | Blue/white | Ignition driver 4 / shift-light driver |
| 20 | Brown | Fuel pump relay driver |
| 21 | Yellow/orange | Injector driver 6 / AuxOut21 |
| 22 | Orange/pink | IACV3 / AuxOut22 |
| 23 | Yellow/red | Injector driver 2 |
| 24 | Yellow/brown | Injector driver 1 |
| 25 | Green/white | Ignition driver 1 |
| 26 | Yellow/white | Injector driver 3 / AuxOut26 |
| 27 | Orange/slate | IACV4 / AuxOut27 |
| 28 | Red | +12 V supply from main relay or common with pin 11 |
| 29 | Black | ECU ground |
| 30 | Black | Sensor ground |
| 31 | Red | Main crank trigger signal |
| 32 | Black | Crank/cam trigger sensor ground |
| 33 | Blue | Coolant temperature signal |
| 34 | Purple | AuxIn34, commonly MAP |
| 35 | White/red | AuxIn35 / DBW pedal position A |
| 36 | Blue/black | AuxIn36 / AuxOut36 / DBW pedal position B |
Functions separated by slashes depend on configuration. Emerald specifies that pin 30 is for sensor return and must not be connected to battery or chassis ground. Consult the manufacturer drawing for crank and cam shielding and configure ignition drivers before connecting coils.