
SCS Delta 900 is a programmable SCS Delta engine-management controller. Delta 900 is a three-connector SCS ECU. The manufacturer's connector listing includes eight injector outputs, eight ignition outputs, dual throttle H-bridges, two sets of wideband lambda connections, knock inputs, two CAN channels and LIN. Confirm I/O allocation, output ratings and electrical features in the precise wiring document. SXTune 900 hardware reference.
Pinout and connector identification
B1–B2 and B3–B4 are throttle bridges 1 and 2. B9–B10 list injectors 7 and 8; B13–B16 list ignition 5–8. Connector C has separate sets of wideband connections C1–C5 and C13–C17, plus LIN at C8. The complete 900 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune delta900 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
Connector A — AMPSeal 776164-1
| Pin | Name | Description | Notes |
|---|---|---|---|
| 1 | Battery Direct | Battery Supply (15A fuse) | Direct Battery Power 6-15V |
| 2 | Ignition | Ignition Switched Supply (10A fuse) | Ignition Key Input |
| 3 | Power Ground 1 | Power Ground | Power Ground |
| 4 | Low Side Output 1 | 3A Open Collector | Injector 1 |
| 5 | Low Side Output 2 | 3A Open Collector | Injector 2 |
| 6 | Low Side Output 3 | 3A Open Collector | Injector 3 |
| 7 | Low Side Output 4 | 3A Open Collector | Injector 4 |
| 8 | Crank/Cam Ground | Digital Ground | Crank/Cam Sensor Ground |
| 9 | Crank Input | VR/Hall - Software Selectable | Crank Sensor Input |
| 10 | Cam Input 1 | VR/Hall - Software Selectable | Inlet Cam Sensor 1 Input |
| 11 | NTC Input 1 | 3.16K pull-up to VREF | Coolant Temp Input |
| 12 | NTC Input 2 | 3.16K pull-up to VREF | Air Temp Input |
| 13 | Ignition 1 | TTL/Power Ignition Output | Ignition 1 |
| 14 | Ignition 2 | TTL/Power Ignition Output | Ignition 2 |
| 15 | Ignition 3 | TTL/Power Ignition Output | Ignition 3 |
| 16 | Ignition 4 | TTL/Power Ignition Output | Ignition 4 |
| 17 | Analog Input 1 | 47k pull-up to VREF | User Configurable 0-5V Analog Input |
| 18 | Cam Input 2 | VR/Hall - Software Selectable | Cam 2 / Wheel Speed |
| 19 | Analog Ground 1 | Analog Ground | Analog Ground |
| 20 | Lambda 1 Input | Weak bias to 450mV | 0-5V Analog Input |
| 21 | CAN 1H | 120 Ohm Terminated | To PC comms DB9 |
| 22 | CAN 1L | To PC comms DB9 | |
| 23 | Low Side Output 5 | 3A Open Collector MFIO | Injector 5 and Lambda 3 Input |
| 24 | Low Side Output 7 | 3A Open Collector w/ recirc diode | Main Relay/PWM1 |
| 25 | Low Side Output 8 | 3A Open Collector w/ recirc diode | Fuel Pump Relay/PWM2 |
| 26 | Low Side Output 9 | 3A Open Collector w/ recirc diode | PWM3 |
| 27 | Low Side Output 10 | 3A Open Collector w/ recirc diode | PWM4 |
| 28 | Low Side Output 11 | 3A Open Collector with pull-up to VBATT via diode | Tacho Output |
| 29 | Low Side Output 6 | 3A Open Collector MFIO | Injector 6 and Lambda 4 Input |
| 30 | Analog Ground 2 | Analog Ground | Analog Ground |
| 31 | NTC Input 3 | 3.16K pull-up to VREF | NTC1 |
| 32 | Analog Input 2 | 47k pull-up to VREF | TPS1 |
| 33 | Analog Input 3 | 47k pull-up to VREF | MAP |
| 34 | VREF | 500mA 5V supply to sensors | 5V Reference |
| 35 | Power Ground 2 | Power Ground | Power Ground 2 |
Connector B — AMPSeal 776163-4
| Pin | Name | Description | Notes |
|---|---|---|---|
| B1 | H Bridge 1 M+ | 5A H-Bridge | Throttle 1 + |
| B2 | H Bridge 1 M- | 5A H-Bridge | Throttle 1 - |
| B3 | H Bridge 2 M+ | 5A H-Bridge | Throttle 2 + |
| B4 | H Bridge 2 M- | 5A H-Bridge | Throttle 2 - |
| B5 | Bipolar Output 1 | 3A Hi Side/Lo Side Drive | PWM5 |
| B6 | Bipolar Output 2 | 3A Hi Side/Lo Side Drive | PWM6 |
| B7 | Bipolar Output 3 | 3A Hi Side/Lo Side Drive | PWM7 |
| B8 | Bipolar Output 4 | 3A Hi Side/Lo Side Drive | PWM8 |
| B9 | Low Side Output 12 | 3A Open Collector | Injector 7 |
| B10 | Low Side Output 13 | 3A Open Collector | Injector 8 |
| B11 | Cam Input 3 | VR/Hall - Software Selectable | Cam 3 |
| B12 | Cam Input 4 | VR/Hall - Software Selectable | Cam 4 |
| B13 | Ignition 5 | TTL/Power | Short circuit protection for Power |
| B14 | Ignition 6 | TTL/Power | Short circuit protection for Power |
| B15 | Ignition 7 | TTL/Power | Short circuit protection for Power |
| B16 | Ignition 8 | TTL/Power | Short circuit protection for Power |
| B17 | Hall Input 1 | Hall Effect Input | Wheel Speed LR |
| B18 | Hall Input 2 | Hall Effect Input | Wheel Speed RR |
| B19 | Hall Input 3 | Hall Effect Input | Wheel Speed LF |
| B20 | Hall Input 4 | Hall Effect Input | Wheel Speed RF |
| B21 | Knock 1 + | ||
| B22 | Knock 2 + | ||
| B23 | Knock Ground | Digital Ground | |
| B24 | Lambda 2 Input | Weak bias to 450mV | Lambda 2 |
| B25 | Analog Input 4 | 47k pull-up to VREF | TPS2 |
| B26 | Analog Input 5 | 47k pull-up to VREF | PPS1 |
| B27 | Analog Input 6 | 47k pull-up to VREF | PPS2 |
| B28 | NTC Input 4 | 3.16k pull-up to VREF | NTC2 |
| B29 | NTC Input 5 | 3.16k pull-up to VREF | NTC3 |
| B30 | Analog Input 7 | 47k pull-up to VREF | TPS3 |
| B31 | Analog Input 8 | 47k pull-up to VREF | TPS4 |
| B32 | Analog Input 9 | 47k pull-up to VREF | Linear 7 |
| B33 | Analog Input 10 | 47k pull-up to VREF | Linear 8 |
| B34 | CAN 2L | 120 Ohm Terminated | |
| B35 | CAN 2H |
Connector C — AMPSeal 776163-2
| Pin | Name | Description | Notes |
|---|---|---|---|
| C1 | Wideband Lambda 1 Heater | 1.7A Open collector with recirc diode (LSU Pin 3) | Wideband Lambda Sensor Heater Output |
| C2 | Wideband Lambda Ip | LSU Pin 1 | Wideband Lambda Sensor Ip |
| C3 | Wideband Lambda Ia | LSU Pin 5 | Wideband Lambda Sensor Ia |
| C4 | Wideband Lambda Virtual Ground (Vm) | LSU Pin 2 | Wideband Lambda Sensor Vm |
| C5 | Wideband Lambda 1 Nernst (Un) | LSU Pin 6 | Wideband Lambda Sensor Un |
| C6 | Hall Input 6 | Cam Sensor 3 Input | |
| C7 | Hall Input 7 | Cam Sensor 4 Input | |
| C8 | LIN | ||
| C9 | L/S Output 14 | 0.75A Open collector with recirc diode | |
| C10 | L/S Output 15 | 0.75A Open collector with recirc diode | |
| C11 | VREF2 | 200mA 5V supply to sensors | |
| C12 | Analog Ground 2 | Analog Ground | |
| C13 | Wideband Lambda 2 Heater | 1.7A Open collector with recirc diode (LSU Pin 3) | Wideband Lambda Sensor Heater Output |
| C14 | Wideband Lambda Ip | LSU Pin 1 | Wideband Lambda Sensor Ip |
| C15 | Wideband Lambda Ia | LSU Pin 5 | Wideband Lambda Sensor Ia |
| C16 | Wideband Lambda Virtual Ground (Vm) | LSU Pin 2 | Wideband Lambda Sensor Vm |
| C17 | Wideband Lambda 2 Nernst (Un) | LSU Pin 6 | Wideband Lambda Sensor Un |
| C18 | Analog Input 11 | 47k pull-up to VREF | |
| C19 | Analog Input 12 | 47k pull-up to VREF | |
| C20 | Analog Input 13 | 47k pull-up to VREF | |
| C21 | Low Side Output 16 | 1.5A Open collector with recirc diode | |
| C22 | Low Side Output 17 | 1.5A Open collector with recirc diode | |
| C23 | Low Side Output 18 | 1.5A Open collector with recirc diode | |
| C24 | Low Side Output 19 | 1.5A Open collector with recirc diode | |
| C25 | Low Side Output 20 | 1.7A Open collector | |
| C26 | Low Side Output 21 | 1.7A Open collector | |
| C27 | Low Side Output 22 (Relay Drive) | 0.75A Open collector with recirc diode | |
| C28 | Low Side Output 23 (Relay Drive) | 0.75A Open collector with recirc diode | |
| C29 | Low Side Output 24 (Relay Drive) | 0.75A Open collector with recirc diode | |
| C30 | Low Side Output 25 (Relay Drive) | 0.75A Open collector with recirc diode | |
| C31 | Low Side Output 26 (Relay Drive) | 0.75A Open collector with recirc diode | |
| C32 | Hall Input 5 | Hall Effect Input (2k7 Pull-up to 5V) | |
| C33 | NTC Input 6 | 3.16k pull-up to VREF | |
| C34 | VREF3 | 200mA 5V supply to sensors | |
| C35 | Analog Ground 3 | Analog Ground |
PC communications connectors
| Pin | Name | Description | Notes |
|---|---|---|---|
| DB9-1 | Ground | ||
| DB9-6 | CAN High | ||
| DB9-7 | CAN Low | ||
| DB9-8 | Battery Voltage |
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.