
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as McLaren 720S, with product code S7plus-M720. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs McLaren 720S installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs McLaren 720S product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs McLaren 720 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The table describes the 720 kit ECU connectors; the vehicle loom and any additional expander connections are outside this schedule. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.
Connector A
| Pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | Main Relay |
| A2 | H‐Bridge1 / SlaveOut1 | H-Bridge1 | DBW1 |
| A3 | H‐Bridge2 / SlaveOut2 | H-Bridge2 | DBW1 |
| A4 | H‐Bridge3 / SlaveOut3 | H-Bridge3 | DBW2 |
| A5 | H‐Bridge4 / SlaveOut4 | H-Bridge4 | DBW2 |
| A6 | H‐Bridge5 / SlaveOut5 | H-Bridge5 | VVT1 In |
| A7 | H‐Bridge6 / SlaveOut6 | H-Bridge6 | VVT2 In |
| A8 | H‐Bridge7 / SlaveOut7 | H-Bridge7 | VVT1 Ex |
| A9 | H‐Bridge8 / SlaveOut8 | H-Bridge8 | VVT2 Ex |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Primary Injector 4 |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | Primary Injector 5 |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | Primary Injector 6 |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | Primary Injector 7 |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | Primary Injector 8 |
| A18 | FUEL9 | PWM OUTPUT | Secondary Injector 1 |
| A19 | FUEL10 | PWM OUTPUT | Secondary Injector 2 |
| A20 | FUEL11 | PWM OUTPUT | Secondary Injector 3 |
| A21 | FUEL12 | PWM OUTPUT | Secondary Injector 4 |
| A22 | FUEL13 | PWM OUTPUT | Secondary Injector 5 |
| A23 | FUEL14 | PWM OUTPUT | Secondary Injector 6 |
| A24 | FUEL15 | PWM OUTPUT | Secondary Injector 7 |
| A25 | FUEL16 | PWM OUTPUT | Secondary Injector 8 |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | IGN1&4 |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | IGN5&8 |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | IGN2&3 |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | IGN6&7 |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | ThermoStat x 2 |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | Starter LS |
| A32 | PWRGND | POWER GROUND | — |
| A33 | PWRGND | POWER GROUND | Ground |
| A34 | PWRGND | POWER GROUND | Ground |
Connector B
| Pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | — |
| B2 | CAN 2L | Can 2 | Can Link to Expander |
| B3 | CAN 2H | Can 2 | Can Link to Exander |
| B4 | KNOCK | KNOCK | — |
| B5 | KNOCK 2 | KNOCK 2 | — |
| B6 | PVBAT | Constant 12 V | — |
| B7 | IVBAT | 12 V | — |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | Pin6 on LSU4.9 Connector |
| B9 | LAM1B | Lami / LamD1‐ /LamIP1 | Pin1 on LSU4.9 Connector |
| B10 | LAM1C | LamLIA1 | Pin5 on LSU4.9 Connector |
| B11 | LAM1D | LamGND / LamLVM1 | Pin2 on LSU4.9 Connector |
| B12 | LAM1HEATER | LAMBDA HEATER | Pin3 on LSU4.9 Connector |
| B13 | IVBAT | 12 V | — |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | Pin6 on LSU4.9 Connector |
| B15 | LAM2B | Lami / LamD1‐ /LamIP1 | Pin1 on LSU4.9 Connector |
| B16 | LAM2C | LamLIA1 | Pin5 on LSU4.9 Connector |
| B17 | LAM2D | LamGND / LamLVM1 | Pin2 on LSU4.9 Connector |
| B18 | LAM2HEATER | LAMBDA HEATER | Pin3 on LSU4.9 Connector |
| B19 | IVBAT | 12 V | Starter relay HS |
| B20 | KLINE | Kline | Alternator LIN |
| B21 | RS232RX | RS232RX | — |
| B22 | RS232TX | RS232TX | — |
| B23 | LANRX‐ | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX‐ | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| Pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| C1 | KNOCKGND | KNOCKGND | — |
| C2 | ANGND | SENSOR GND | B Sensor Grounds |
| C3 | ANGND | SENSOR GND | — |
| C4 | ANGND | SENSOR GND | — |
| C5 | 5V OUT | 5V OUT | — |
| C6 | 5V OUT | 5V OUT | A 5v |
| C7 | 5V OUT | 5V OUT | — |
| C8 | CAN L | Can Low | — |
| C9 | CAN H | Can High | — |
| C10 | AN01 | BI-POLAR INPUTS | Crank Sensor |
| C11 | AN02 | BI-POLAR INPUTS | VVT1IN |
| C12 | AN03 | BI-POLAR INPUTS | VVT2IN |
| C13 | AN04 | BI-POLAR INPUTS | VVT1Ex |
| C14 | AN05 | UNI-POLAR INPUTS | VVT2Ex |
| C15 | AN06 | UNI-POLAR INPUTS | MAP Manifold |
| C16 | AN07 | UNI-POLAR INPUTS | TPS2A |
| C17 | AN08 | UNI-POLAR INPUTS | TPS2B |
| C18 | AN09 | VOLT-INPUTS | PPS1 |
| C19 | AN10 | VOLT-INPUTS | PPS2 |
| C20 | AN11 | VOLT-INPUTS | TPS1A |
| C21 | AN12 | VOLT-INPUTS | TPS1B |
| C22 | AN13 | RESISTIVE INPUTS | ACT1 |
| C23 | AN14 | RESISTIVE INPUTS | Park Neutral Sw |
| C24 | AN15 | RESISTIVE INPUTS | Coolant temp |
| C25 | AN16 | RESISTIVE INPUTS | Coolant temp 2 |
| C26 | Can3 L | Can3 L | TCM CAN |
| C27 | Can3 H | Can3 H | TCM CAN |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | 12v Ignition |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | Fuel Pressure |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | Fuel Temp |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | ISG |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | Oil pressure switch |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | Map 1 |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | Map2 |