
Link G4X MX5X is a vehicle-specific programmable plug-in ECU for the Mazda MX-5 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's MX5X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The MX5X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
MX5Link main header and expansion connectors
From the Link MX5Link installation manual, pages 18–21. Main-header functions vary between MX5 1600, MX5 1800 and GTX/GTR wiring. This table gives the Link ECU channels; consult the manufacturer’s vehicle-specific columns before associating a channel with a factory function. Pin designations 27–30 do not appear in the manufacturer table. Views are looking into the ECU from the wire side; nc is as stated by Link.
| Pin | Mazda cavity | Link channel |
|---|---|---|
| 1 | 2Y | Injector 3 |
| 2 | 2W | Aux 1 |
| 3 | 2U | Injector 1 |
| 4 | 2S | Aux 2 |
| 5 | 2Q | An Temp 1 |
| 6 | 2O | An Volt 4 |
| 7 | 2M | An Volt 1 |
| 8 | 2K | +5 V Out |
| 9 | 2I | Tacho pull-up |
| 10 | 2G | Trig 2 |
| 11 | 2E | Trig 1 |
| 12 | 2C | Ground (signal) |
| 13 | 2A | Ground |
| 14 | 2Z | Injector 4 |
| 15 | 2X | Aux 7 |
| 16 | 2V | Injector 2 |
| 17 | 2T | Aux 5 |
| 18 | 2R | Aux 6 |
| 19 | 2P | An Temp 2 |
| 20 | 2N | An Volt 2 |
| 21 | 2L | nc |
| 22 | 2J | nc |
| 23 | 2H | nc |
| 24 | 2F | Ground |
| 25 | 2D | Ground (signal) |
| 26 | 2B | Ground |
| 31 | 1U | nc |
| 32 | 1S | nc |
| 33 | 1Q | DI 1 |
| 34 | 1O | nc |
| 35 | 1M | DI 3 |
| 36 | 1K | nc |
| 37 | 1I | Aux 3 |
| 38 | 1G | Ignition 1 |
| 39 | 1E | Aux 4 |
| 40 | 1C | DI 4 |
| 41 | 1A | nc (constant +12 V) |
| 42 | 1V | DI 5 |
| 43 | 1T | nc |
| 44 | 1R | Aux 8 |
| 45 | 1P | DI 2 |
| 46 | 1N | nc |
| 47 | 1L | Ignition 4 (Aux) |
| 48 | 1J | Ignition 3 (Aux) |
| 49 | 1H | Ignition 2 |
| 50 | 1F | nc |
| 51 | 1D | nc |
| 52 | 1B | +14 V main relay |
The built-in MAP sensor is An Volt 3. The manual states injector drives 7 and 8 are not exposed and lack injector-drive hardware. Manual-transmission 1.6 NA cars have throttle switches rather than an analogue TPS; a wiring change is needed for an analogue TPS. If deleting the 1.6 NA MAF, the fuel-pump circuit needs modification for ECU control.
Expansion connector
| Pin | Link channel |
|---|---|
| 1 | Ground (signal) |
| 2 | +5 V Out |
| 3 | DI 7 |
| 4 | DI 6 |
| 5 | An Volt 5 |
| 6 | An Volt 6 |
| 7 | An Temp 4 |
| 8 | An Temp 3 |
| 9 | Ground (signal) |
| 10 | +5 V Out |
| 11 | Ignition 7 (Aux) |
| 12 | Ignition 8 (Aux) |
| 13 | DI 8 |
| 14 | DI 9 |
| 15 | An Volt 10 |
| 16 | An Volt 11 |
On bottom board V1.4 and earlier Link reports An Volt 10 and 11 are incorrectly labelled An Volt 9 and 10 on the expansion plugs. Signal ground is for isolated sensors, not a chassis-ground connection.
CAN 1 / RS232 connector
| Pin | Function / cable colour |
|---|---|
| 1 | Comms GND (brown) |
| 2 | CAN1 L (green) |
| 3 | CAN1 H (white) |
| 4 | RS232 RX (grey) |
| 5 | RS232 TX (yellow) |
When using CAN, Link cautions that connected serial wires can interfere with USB communications.
CAN 2 / OBD connector
| Pin | Function / cable colour |
|---|---|
| 1 | GND (brown) |
| 2 | CAN2 L (green) |
| 3 | CAN2 H (white) |
| 4 | NC (grey) |
| 5 | +14 V (yellow) |