Tuning Wiki
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan 370Z Manual Auto S7Plus, with product code S7Plus-N370Z. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan 370Z Manual Auto S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Manufacturer ECU connector schedules

From the Syvecs Nissan 370Z installation guide, revision 1.2. These are ECU-side connections and the manufacturer's application notes; the guide does not give a complete factory vehicle-connector schedule. For A1, consult the drawing for the diode between the relay pins. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.

Connector A

ECU pinSyvecs description370Z application notes
A1PWR CTR OUTThrottle and main relay; see the manual for the diode between pins 24 and 25
A2H‐Bridge1 / SlaveOut1DBW
A3H‐Bridge2 / SlaveOut2DBW
A4H‐Bridge3 / SlaveOut3DBW
A5H‐Bridge4 / SlaveOut4DBW
A6H‐Bridge5 / SlaveOut5SPARE
A7H‐Bridge6 / SlaveOut6Fuel Pump Relay
A8H‐Bridge7 / SlaveOut7Evap
A9H‐Bridge8 / SlaveOut8VVEL Signal
A10FUEL1Primary Injector 1
A11FUEL2Primary Injector 2
A12FUEL3Primary Injector 3
A13FUEL4Primary Injector 4
A14FUEL5Primary Injector 5
A15FUEL6Primary Injector 6
A16FUEL7Secondary Injector 1 Or Spare Ouput
A17FUEL8Secondary Injector 2 Or Spare Ouput
A18PWM1 /*FUEL9Secondary Injector 3 Or Spare Ouput
A19PWM2 / *FUEL10Secondary Injector 4 Or Spare Ouput
A20PWM3 / *FUEL11Spare
A21PWM4 / *FUEL12Secondary Injector 5 Or Spare Ouput
A22PWM5Secondary Injector 6 Or Spare Ouput
A23PWM6Tacho
A24PWM7VVT1
A25PWM8VVT2
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGND—
A33PWRGND—
A34PWRGND—

Connector B

ECU pinSyvecs description370Z application notes
B1PWRGND—
B2CAN2L—
B3CAN2H—
B4KNOCK—
B5KNOCK 2—
B6PVBAT—
B7IVBAT—
B8LAM1A2.2v
B9LAM1B1.8v
B10LAM1C—
B11LAM1D—
B12LAM1HEATER—
B13IVBAT—
B14LAM2A2.2v
B15LAM2B1.8v
B16LAM2C—
B17LAM2D—
B18LAM2HEATER—
B19IVBAT—
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX‐—
B24LANRX+—
B25LANTX‐—
B26LANTX+—

Connector C

ECU pinSyvecs description370Z application notes
C1KNOCKGNDKnock Ground
C2ANGNDBrake Booster, TPS, Gear Lever
C3ANGNDCrank, ACT
C4ANGNDECT
C55V OUTTPS, Brake Booster, Gear lever
C65V OUTCrank
C75V OUTPPS
C8CAN LCan Low
C9CAN HCan High
C10AN01TPS 1A
C11AN02TPS 1B
C12AN03TPS 2A
C13AN04TPS2B
C14AN05Cam Position Sensor
C15AN06Crank Position Sensor
C16AN07Cam2 Position Sensor
C17AN08Oil Temp
C18AN09MAP Absolute Sensor
C19AN10PPS1
C20AN11PPS2
C21AN12Brake Switch
C22AN13Clutch Sw
C23AN14Air Charge Temp
C24AN15Coolant Temp
C25AN16Cruise Control SW
C26EGT1-Flying TC Lead
C27EGT1+Flying TC Lead
C28PWR CTR INIgnition Switch
C29AN S1 / Slave An01Power Steering Pressure
C30AN S2 / Slave An02Maf 1 / Spare Input /
C31AN S3 / Slave An03Maf2 / Spare Input/
C32AN S4 / Slave An04Brake Booster /
C33AN S5 / Slave An05Gear Lever Position X / DONT REMOVE ON MANUAL
C34AN S6 / Slave An06Gear Lever Position Y / DONT REMOVE ON MANUAL

Directly applicable articles

Technical articles assigned to this context will appear here.