
Vi-PEC iSupra is a iSeries plug-in ECU documented for Toyota Supra 2JZ non-VVT. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named iSeries plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link identifies PCLink G4+ for iSeries hardware. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
These are all positions listed in the application-specific Vi-PEC installation guide, page 20. The guide specifies the view looking into the ECU from the wire side. Positions omitted by the guide are not assumed unused; functions must be configured for the vehicle. The guide names Toyota Supra 92–97 in the pinout section and 93–98 2JZ-GTE in its function listing. Both B71 and B72 are labelled Inj 7 in the pinout, while the function list also mentions Inj 8; confirm the correct assignment and exact car before wiring.
Main ECU connector: documented positions
| Position | ECU function |
|---|---|
| A1 | DI 2 |
| B43 | An Volt 5 |
| A2 | DI 1 |
| B44 | An Temp 1 |
| A4 | DI 6 |
| B45 | An Temp 2 |
| A6 | Ign 7 |
| B47 | An Volt 4 |
| A15 | DI 4 |
| B48 | An Volt 3 |
| A16 | Aux 1 |
| B49 | Knock 2 |
| A22 | Aux 2 |
| B50 | Knock 1 |
| A23 | Aux 3 |
| B52 | Ign 6 |
| A34 | DI 3 |
| B53 | Ign 5 |
| B15 | Inj 6 |
| B54 | Ign 4 |
| B16 | Inj 5 |
| B55 | Ign 3 |
| B17 | Inj 4 |
| B56 | Ign 2 |
| B18 | Inj 3 |
| B57 | Ign 1 |
| B19 | Inj 2 |
| B60 | Aux 4 |
| B20 | Inj 1 |
| B62 | An Volt 1 |
| B25 | Trig 2 |
| B65 | Sensor GND |
| B27 | Trig 1 |
| B66 | An Volt 2 |
| B32 | Aux 8 |
| B71 | Inj 7 |
| B33 | Aux 6 |
| B72 | Inj 7 |
| B34 | Aux 7 |
| B73 | Ign 8 |
| B35 | Aux 5 |
| B74 | Aux 10 |
| B41 | +5 Volt out |
| B76 | DI5 |
Expansion connector functions
The guide also lists sensor ground, low-current +5 V, An Volt 6 and 7, An Temp 3 and 4, and DI 7 and 8 on the expansion connector, but does not assign cavity numbers in this section. Do not infer their order.