A camshaft only does what its card promises if it is phased correctly to the crankshaft. Degreeing is the measurement that checks and, where needed, corrects that phasing. This page explains the method in outline. The cam maker's instructions for the exact camshaft and engine come first. For cam geometry see camshafts and valve timing, and for the limits the valvetrain sets see valve springs, valve float and rev limits.
Why degree a cam
Camshaft and crankshaft timing marks, gears and keyways have manufacturing tolerances, and a few degrees of error moves the cam's effect noticeably. Degreeing measures the actual position of the cam against the crank and compares it with the cam card. If the numbers differ, the timing can be advanced or retarded with an adjustable gear, an offset key or an offset bushing (DSPORT: degreeing a DOHC engine).
Tools
- A degree wheel, fitted to the crank snout or damper, with a fixed pointer.
- A dial indicator with enough travel for the valve or lifter lift, on a stable magnetic base, aligned with the direction of valve movement.
- A positive piston stop or a deck bridge with a dial indicator to find true top dead centre, because the marked TDC on a damper or wheel can be wrong.
Finding true TDC
With a deck bridge and indicator centred over the number one piston (which limits error from the piston rocking), bring the piston up to 0.050 in before TDC and record the degree-wheel reading, then take it 0.050 in past TDC and record that reading. The midpoint of the two readings is true TDC. Rotate the wheel so that midpoint sits at the pointer, which sets zero at TDC (Dragzine: degreeing with Erson Cams). A piston stop threaded into the spark plug hole is the other common method; remove it before turning the engine, because leaving it in can bend valves.
Finding the intake centreline
- Mount the indicator on the number one intake lifter or valve, with the plunger aligned and the lash taken up.
- Find peak lift. Back off a small amount on the opening side, for example 0.020 in before peak, and record the wheel reading. Go the same distance past peak on the closing side and record that reading.
- Add the two readings and divide by two. The result is the intake centreline, the crank angle of maximum valve lift. As an example, readings of 68° before and 152° after peak give 220°, and 220 ÷ 2 gives a 110° centreline (this is an illustration, not a specification).
- Compare it with the figure on the cam card.
The offset either side of peak compensates for differences between the opening and closing sides of the profile. Not all cam makers define their numbers at the same point, so check the cam card's convention before comparing figures. Repeat for the exhaust cam on an engine with separate cams.
Correcting it and checking clearance
If the measured centreline does not match the card, adjust the cam with an adjustable gear or offset parts and measure again until it matches. Advancing or retarding the cam changes where in the rev range it works, and changes the valve-to-piston clearance, so check the clearance after any change. A higher-lift or longer-duration cam, or one that has been moved from the card position, is one of the geometry checks described on engine displacement. Turn the engine by hand through two full revolutions after any timing change to check nothing touches.
Checks after the engine runs
- Check the timing belt or chain tension and alignment after fitting, as the maker specifies.
- Confirm the ignition timing against a reference: ignition tuning, and that the ECU's cam and crank sensors still agree after a timing change: crankshaft and camshaft position sensors.
- Log the engine, and check the calibration still suits the changed cam: ECU remapping. For a new camshaft, the run-in procedure is on engine break-in after a rebuild.
Sources
- How To Degree A Camshaft With Erson Cams. Steve Baur, Dragzine, 23 August 2023. True TDC, intake centreline method and offsets. Accessed 2026-11-19.
- Why and How to Degree Your DOHC Engine. DSPORT Magazine, 15 September 2015 (no author listed). Tools, piston stop, cam card and adjustable gears. Accessed 2026-11-19.