Tuning Wiki

MaxxECU GEN2 RACE — New-generation ECU with sixteen peak-and-hold injector outputs and twelve selectable ignition/general-purpose outputs for up to twelve sequential cylinders. MaxxECU product information.

MaxxECU GEN2 RACE
MaxxECU GEN2 RACE, manufacturer product image: MaxxECU. Used with permission.

Model identification and capabilities

GEN2 RACE has 24 analogue and eight VR/Hall pulse inputs, eight type-K EGT inputs, dual wideband and dual knock. Its 550 kPa absolute MAP sensor, dual CAN, Wi-Fi, Bluetooth, USB-C and IP68-rated enclosure are identified on the manufacturer’s product page. Wideband support includes LSU 5.2, 4.9 and 4.2. Manufacturer specification; MaxxECU model comparison.

Sequential cylinders, maximum12
Injector outputs16 peak-and-hold
Ignition outputs12 selectable ignition/GP
ConfigurationMTune; check the release appropriate to the ECU and hardware revision

Identification and installation

GEN2 RACE has MX1 through MX4 connectors. MX3 differs from GEN2 TRACK; MX1 and MX2 are shared across the GEN2 SPORT, TRACK and RACE with model-dependent positions; MX4 belongs to RACE. Check diagram version and hardware revision.

Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.

Connectors and pinout

The following positions follow the RACE column in MaxxECU's GEN2 wiring reference. Blank values in model-specific columns inherit the adjacent shared function; explicitly unavailable positions are retained. Check the physical connector drawing before wiring.

Connector MX1

From the manufacturer's GEN2 RACE connector reference; establish the connector view and check wiring and current limits in the original.

PinFunctionNote
1Ignition 1
2Ignition 2
3Ignition 3
4Ignition 4
5GP out 1 (GND)
6GP out 2 (GND)
7GP out 3 (GND)
8GP out 4 (GND)
9Engine gndTo engine cylinder head.
10Digital/VR 1 (PULSE) SIGNAL +
11Digital/VR 1 (PULSE) SIGNAL -
12Digital/VR 1 (PULSE) POWER SUPPLY
13Digital/VR 1 (PULSE) SHIELD
14SENSOR GNDMust NOT be connected to engine GND
15CAN L
16CAN H
17GP out 5 (GND)
18Digital/VR 2 (PULSE) SIGNAL +
19Digital/VR 2 (PULSE) SIGNAL -
20Digital/VR 2 (PULSE) POWER SUPPLY
21Digital/VR 2 (PULSE) SHIELD
225V power supply
23Digital/VR 3 (PULSE) SIGNAL +
24Digital/VR 4 (PULSE) SIGNAL +
2512V supply 1Main ECU supply.
26AIN 1
27AIN 2
28AIN 3
29AIN 4
30AIN 5
31INJECTOR 1
32INJECTOR 2
33INJECTOR 3
34INJECTOR 4

Connector MX2

From the manufacturer's GEN2 RACE connector reference; establish the connector view and check wiring and current limits in the original.

PinFunctionNote
1Ignition 5
2Ignition 6
3GP out 6 (GND)
4AIN 6
5AIN 7
6AIN 8
7GP out 13 (H-BRIDGE 1)
8GP out 14 (H-BRIDGE 1)
9Engine gndTo engine cylinder head.
10WBO2 Sensor 1 VS
11WBO2 Sensor 1 COM/VREF
12GP OUT 7 / WBO2 Sensor 1 H-
13AIN 9
14AIN 10
15AIN 11
16AIN 12
17AIN 13
18WBO2 sensor 1 RCAL
19WBO2 sensor 1 IP
2012V WBO2 sensor 1 H+
21WBO2 sensor 1 SHIELD
22AIN 14
23AIN 15
2412V supply 3Used for ignition key or to power the internal RTC
2512V supply 2Must be wired if 12V driving output exceeds 10A
26KNOCK1 SHIELD
27KNOCK 1-
28KNOCK 1+
29KNOCK 2 SHIELD
30KNOCK 2-
31KNOCK 2+
32AIN 16
33INJECTOR 5
34INJECTOR 6

Connector MX3

From the manufacturer's GEN2 RACE connector reference; establish the connector view and check wiring and current limits in the original.

PinFunctionNote
1GP out 15 (H-BRIDGE 2)
2GP out 16 (H-BRIDGE 2)
3Ignition 7
4Ignition 8
5Ignition 9
6Ignition 10
7Ignition 11
8Ignition 12
9Engine gndTo engine cylinder head.
10WBO2 sensor 2 VS
11WBO2 sensor 2 COM/VREF
12GP Out 8 (GND) / WBO2 Sensor 2 H-
13WBO2 sensor 2 SHIELD
14GP OUT 9 (12V)
15GP OUT 10 (12V)
16GP OUT 11 (12V)
17GP OUT 12 (12V)
18WBO2 sensor 2 RCAL
19WBO2 sensor 2 IP
2012V WBO2 sensor 2 �(H+)
21AIN 17
22AIN 18
23AIN 19
24AIN 20
25AIN 21
26AIN 22
27AIN 23
28AIN 24
29INJECTOR 7
30INJECTOR 8
31INJECTOR 9
32INJECTOR 10
33INJECTOR 11
34INJECTOR 12

Connector MX4

From the manufacturer's GEN2 RACE connector reference; establish the connector view and check wiring and current limits in the original.

PinFunctionNote
1Digital/VR 5 (PULSE) SHIELD
2Digital/VR 5 (PULSE) SIGNAL -
3Digital/VR 5 (PULSE) SIGNAL +
4Digital/VR 6 (PULSE) SHIELD
5Digital/VR 6 (PULSE) SIGNAL -
6Digital/VR 6 (PULSE) SIGNAL +
7Digital/VR 7 (PULSE) SHIELD
8Digital/VR 7 (PULSE) SIGNAL -
9Digital/VR 7 (PULSE) SIGNAL +
10EGT 1 +(yellow)
11EGT 2 +(yellow)
12EGT 3 +(yellow)
13EGT 4 +(yellow)
14EGT 5 +(yellow)
15EGT 6 +(yellow)
16EGT 7 +(yellow)
17EGT 8 +(yellow)
18EGT 1 -(red)
19EGT 2 -(red)
20EGT 3 -(red)
21EGT 4 -(red)
22EGT 5 -(red)
23EGT 6 -(red)
24EGT 7 -(red)
25EGT 8 -(red)
26Digital/VR 8 (PULSE) SHIELD
27Digital/VR 8 (PULSE) SIGNAL -
28Digital/VR 8 (PULSE) SIGNAL +
29CAN 2 L
30CAN 2 H
31INJECTOR 13
32INJECTOR 14
33INJECTOR 15
34INJECTOR 16

Software and further documents

Sources reviewed 17 November 2026.

Directly applicable articles

Technical articles assigned to this context will appear here.