Adaptronic eSel004B is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda MX-5 / Miata NA8C (1996–1997), naturally aspirated BP without variable valve timing. Adaptronic eSel004B application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel004B guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel004B guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says connector 2 has no factory loom plug, NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The source assigns auxiliary output 3 to both 1B and 1G; retain and verify the manufacturer configuration.
| Factory pin | Factory function | Adaptronic function | Installation notes |
|---|---|---|---|
| A / 1A | Radiator Fan Relay | Aux Output 7 | — |
| B / 1B | Condensor Fan Relay | Aux Output 3 | — |
| C / 1C | Starter Input | — | — |
| D / 1D | Data Link | Aux Output 2 | — |
| E / 1E | Check Light | Aux Output 6 | — |
| F / 1F | NC | — | — |
| G / 1G | Aircon Clutch Output | Aux Output 3 | — |
| H / 1H | Headlights | Digital Input 5 | — |
| I / 1I | Data Link | CAS3 | Optional flex fuel. |
| J / 1J | Defogger | Digital Input 8 | — |
| K / 1K | Aircon Request | Digital Input 2 | — |
| L / 1L | Neutral Switch | Digital Input 6 | — |
| M / 1M | MVSS | MVSS1 | Gearbox speed or rear-left wheel speed. |
| N / 1N | NC | MVSS2 | Optional flex fuel or rear-right speed. |
| O / 1O | Junction GND | PGND | — |
| P / 1P | Blower (electrical load) | Digital Input 4 | — |
| Q / 1Q | Brake Pedal Switch | Digital Input 3 | — |
| R / 1R | AT | — | — |
| S / 1S | NC | SVSS1 | Optional flex fuel or front-left speed. |
| T / 1T | AT | SVSS2 | Optional front-right speed. |
| U / 1U | Fuel Pump Relay | Aux Output 5 | — |
| V / 1V | NC | — | — |
| 3A | NC | AuxT | — |
| 3B | Airflow | MAF | — |
| 3C | O2 Signal | O2 signal input | For 0–1 V sensors; 3 V maximum. |
| 3D | — | Knock | — |
| 3E | NC | — | — |
| 3F | TPS Signal | TPS | — |
| 3G | Coolant Temp Signal | ECT | — |
| 3H | EGR Boost Sensor | Spare | Spare 0–5 V input; manufacturer recommends serial for wideband. |
| 3I | TPS 5V | +5V output | Sensor +5 V supply. |
| 3J | EGR Position Sensor | — | — |
| 3K | Inlet Air Temp | MAT | — |
| 3L | TPS Closed Throttle SW | Digital Input 7 | — |
| 3M | Front O2 Heater Ground | PGND | — |
| 3N | EGR Boost Sensor | — | — |
| 3O | Sensor GND | GND | — |
| 3P | Power Steering SW | Digital Input 1 | — |
| 4A | Power GND | PGND | — |
| 4B | Ign Power | 12V | — |
| 4C | Power GND | PGND | — |
| 4D | Power GND | PGND | — |
| 4E | Crank sensor | — | — |
| 4F | Cam sensor 1 | CAS1 input | Four pulses; ignition timing. |
| 4G | Cam sensor 2 | CAS2 input | Two pulses; cylinder identification. |
| 4H | Crank sensor | — | — |
| 4I | Constant Power | Constant Pwr | — |
| 4J | PRCV | — | — |
| 4K | NC | — | — |
| 4L | Tacho | Ignition output 3 | Tachometer function. |
| 4M | NC | Ignition Output 4 | Optional direct-fire conversion. |
| 4N | Ignition 1 (1&4) | Ignition Output 1 | — |
| 4O | EGR vent valve | — | — |
| 4P | EGR Vac valve | — | — |
| 4Q | Idle Control | Aux Output 1 | — |
| 4R | Ignition 2 (2&3) | Ignition Output 2 | — |
| 4S | NC | — | — |
| 4T | Purge Valve | Aux Output 4 | — |
| 4U | Injector cyl 1 | Injector Output 1 | — |
| 4V | Injector cyl 2 | Injector Output 4 | — |
| 4W | Injector cyl 3 | Injector Output 2 | — |
| 4X | Injector cyl 4 | Injector Output 3 | — |
| 4Y | AT | — | — |
| 4Z | NC | — | — |
Manufacturer photograph
