
Vi-PEC V Series Mitsubishi EVO 4-8 is a V Series plug-in ECU documented for Mitsubishi Lancer EVO 4–8. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, are shown below. The drawing uses a view looking into the ECU from the wire side. Positions omitted by the source are not assumed unused; configure the channels for the vehicle. Auxiliary 2 is routed to pin 55 for EVO 4–7 or pin 57 for EVO 8 using the board jumper. The guide also repeats Aux–Ign 4 at pins 20, 32 and 34; verify the relevant loom and configuration.
Main ECU connector: documented positions
| Position | ECU function |
|---|---|
| 1 | Injection 1 |
| 55 | Aux 2 (Jumper EVO 4-7) |
| 2 | Injection 3 |
| 57 | Aux 2 (Jumper EVO 8) |
| 4 | Aux 5 |
| 58 | Aux 3 |
| 5 | Aux 7 |
| 71 | DI 2 |
| 8 | Inj 5 |
| 72 | An Temp 2 |
| 10 | Ignition 1 |
| 73 | An Volt 1 |
| 11 | Aux 4 |
| 76 | An Volt 4 |
| 14 | Injection 2 |
| 77 | An Temp 3 |
| 15 | Injection 4 |
| 82 | DI 1 |
| 17 | Aux 6 |
| 83 | An Temp 1 |
| 18 | Aux 8 |
| 84 | An Volt 3 |
| 20 | Aux - Ign 4 |
| 86 | DI 4 |
| 21 | Aux 1 |
| 90 | An Volt 2 |
| 22 | Ignition 3 |
| 91 | DI 3 |
| 12 | +14V Main Relay |
| 13 | Ground |
| 23 | Ignition 2 |
| 92 | Sensor Ground |
| 32 | Aux – Ign 4 |
| 34 | Aux – Ign 4 |
| 35 | Aux – Ign 5 |
| 36 | Aux – Inj 7 |
| 37 | An Volt 5 |
| 38 | Aux – Inj 8 |
| 39 | Aux – Inj 6 |
| 44 | DI 5 |
| 45 | DI 6 |
Other connections
| Position | ECU function |
|---|---|
| Expansion 1 | Signal Ground |
| Expansion 2 | +5V Out |
| Expansion 3 | DI 7 N/C |
| Expansion 4 | DI 8 N/C |
| Expansion 5 | An Volt 6 |
| Expansion 6 | An Volt 7 |
| Expansion 7 | Temp 4 N/C |
| Expansion 8 | N/C |