
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Nissan R35 GTR 2009-2019 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
R35 kit ECU connector schedules
The Syvecs R35GTR kit manual, pages 10–12, documents the S7Plus ECU connector assignments below. These are ECU pins, not the original Nissan harness pinout. The manufacturer states the 2020-onward kit uses a different vehicle connector; verify the precise adapter and model year before using these assignments.
Connector A — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| A1 | PWR CTR OUT | Throttle and main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | DBW |
| A5 | H-Bridge4 / SlaveOut4 | DBW |
| A6 | H-Bridge5 / SlaveOut5 | Boost solenoid |
| A7 | H-Bridge6 / SlaveOut6 | Fuel pump 2 |
| A8 | H-Bridge7 / SlaveOut7 | Evap |
| A9 | H-Bridge8 / SlaveOut8 | — |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Primary injector 5 |
| A15 | FUEL6 | Primary injector 6 |
| A16 | FUEL7 | Secondary injector 1 or spare |
| A17 | FUEL8 | Secondary injector 2 or spare |
| A18 | PWM1 / *FUEL9 | Secondary injector 3 or spare |
| A19 | PWM2 / *FUEL10 | Secondary injector 4 or spare |
| A20 | PWM3 / *FUEL11 | Fuel pump controller – 5 V pull-up |
| A21 | PWM4 / *FUEL12 | Secondary injector 5 or spare |
| A22 | PWM5 | Secondary injector 6 or spare |
| A23 | PWM6 | Tacho |
| A24 | PWM7 | VVT1 |
| A25 | PWM8 | VVT2 |
| A26 | IGN1 | Ignition 1 |
| A27 | IGN2 | Ignition 2 |
| A28 | IGN3 | Ignition 3 |
| A29 | IGN4 | Ignition 4 |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | Ignition 6 |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
Connector B — 26 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2L | — |
| B3 | CAN2H | — |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | 2.2 V per source |
| B9 | LAM1B | — |
| B10 | LAM1C | — |
| B11 | LAM1D | — |
| B12 | LAM1HEATER | Lambda heater |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | 2.2 V per source |
| B15 | LAM2B | 1.8 V per source |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | Lambda heater |
| B19 | IVBAT | 12 V |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
Connector C — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| C1 | KNOCKGND | — |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | — |
| C9 | CAN H | — |
| C10 | AN01 | TPS1A |
| C11 | AN02 | TPS1B |
| C12 | AN03 | TPS2A |
| C13 | AN04 | TPS2B |
| C14 | AN05 | Cam position sensor |
| C15 | AN06 | Crank position sensor |
| C16 | AN07 | Cam 2 position sensor |
| C17 | AN08 | Oil temperature |
| C18 | AN09 | MAP absolute sensor |
| C19 | AN10 | PPS1 |
| C20 | AN11 | PPS2 |
| C21 | AN12 | Brake switch |
| C22 | AN13 | Fuel temperature |
| C23 | AN14 | Air charge temperature |
| C24 | AN15 | Coolant temperature |
| C25 | AN16 | Cruise control switch |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition switch |
| C29 | AN S1 / Slave An01 | Secondary air injection (flex fuel) |
| C30 | AN S2 / Slave An02 | MAF1 / spare input |
| C31 | AN S3 / Slave An03 | MAF2 / spare input |
| C32 | AN S4 / Slave An04 | — |
| C33 | AN S5 / Slave An05 | Pre-throttle MAP1 / spare input |
| C34 | AN S6 / Slave An06 | Pre-throttle MAP2 / spare input |
The source repeats lambda-1 software labels for the LAM2A–D section. Confirm the second lambda channel with Syvecs rather than assuming the wiring is identical.