
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk2 8P S7Plus, with product code S7Plus-RS3 Mk2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk2 8P S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Audi TTRS RS3 Mk2 8P S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
CEPA kit ECU and DI12 connector schedules
The Syvecs TTRS / RS3 Mk2 manual, version 1.3, explicitly limits this schedule to CEPA engines. These are Syvecs ECU and DI12 driver connector positions, not the vehicle OEM pinout. Confirm the actual engine, adapter, settings and connector orientation. Blank entries mean the source does not specify a kit function.
ECU A — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| A1 | PWR CTR OUT | Main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | Additional coolant pump relay |
| A5 | H-Bridge4 / SlaveOut4 | Fan |
| A6 | H-Bridge5 / SlaveOut5 | Spare output |
| A7 | H-Bridge6 / SlaveOut6 | Oil pressure control valve |
| A8 | H-Bridge7 / SlaveOut7 | Sport lamp |
| A9 | H-Bridge8 / SlaveOut8 | Fuel pump |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Primary injector 5 |
| A15 | FUEL6 | Port injector 1 |
| A16 | FUEL7 | Port injector 2 |
| A17 | FUEL8 | Port injector 3 |
| A18 | PWM1 / *FUEL9 | Port injector 4 |
| A19 | PWM2 / *FUEL10 | Port injector 5 |
| A20 | PWM3 / *FUEL11 | Intake manifold flap |
| A21 | PWM4 / *FUEL12 | Wastegate solenoid |
| A22 | PWM5 / *FUEL13 | Turbo recirculation |
| A23 | PWM6 / *FUEL14 | Exhaust flap |
| A24 | PWM7 / *FUEL15 | VVT1 intake |
| A25 | PWM8 / *FUEL16 | VVT1 exhaust |
| A26 | IGN1 | Ignition 1 |
| A27 | IGN2 | Ignition 2 |
| A28 | IGN3 | Ignition 3 |
| A29 | IGN4 | Ignition 4 |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | DI pump |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
ECU B — 26 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2L | — |
| B3 | CAN2H | — |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | LSU 4.9 connector pin 6 |
| B9 | LAM1B | LSU 4.9 connector pin 1 |
| B10 | LAM1C | LSU 4.9 connector pin 5 |
| B11 | LAM1D | LSU 4.9 connector pin 2 |
| B12 | LAM1HEATER | LSU 4.9 connector pin 3 |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | Source repeats LSU 4.9 pin 6; confirm |
| B15 | LAM2B | Source repeats LSU 4.9 pin 1; confirm |
| B16 | LAM2C | Source repeats LSU 4.9 pin 5; confirm |
| B17 | LAM2D | Source repeats LSU 4.9 pin 2; confirm |
| B18 | LAM2HEATER | Source repeats LSU 4.9 pin 3; confirm |
| B19 | IVBAT | 12 V |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
ECU C — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| C1 | KNOCKGND | — |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | Powertrain CAN |
| C9 | CAN H | Powertrain CAN |
| C10 | AN01 | DI pressure |
| C11 | AN02 | MAP sensor |
| C12 | AN03 | Charge pressure |
| C13 | AN04 | Brake |
| C14 | AN05 | VVT1 intake |
| C15 | AN06 | VVT1 exhaust |
| C16 | AN07 | Crank sensor |
| C17 | AN08 | Clutch position |
| C18 | AN09 | TPS1A |
| C19 | AN10 | TPS1B |
| C20 | AN11 | PPSA |
| C21 | AN12 | PPSB |
| C22 | AN13 | Intake air temperature |
| C23 | AN14 | Intake temperature 2 |
| C24 | AN15 | Coolant temperature |
| C25 | AN16 | — |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | 12 V ignition |
| C29 | AN S1 / Slave An01 | — |
| C30 | AN S2 / Slave An02 | — |
| C31 | AN S3 / Slave An03 | Sport mode |
| C32 | AN S4 / Slave An04 | Exhaust gas temperature |
| C33 | AN S5 / Slave An05 | Low fuel pressure |
| C34 | AN S6 / Slave An06 | Intake flap potentiometer |
DI12 driver — 35 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| 1 | LS1 | Injector 1 − |
| 2 | LS2 | Injector 5 − |
| 3 | LS3 | — |
| 4 | LS4 | — |
| 5 | LS5 | Injector 2 − |
| 6 | LS6 | Injector 3 − |
| 7 | LS12 | — |
| 8 | LS11 | — |
| 9 | LS10 | — |
| 10 | LS9 | — |
| 11 | LS8 | — |
| 12 | LS7 | Injector 4 − |
| 13 | Input 1 | Injector 1 signal |
| 14 | Input 2 | Injector 5 signal |
| 15 | Input 3 | — |
| 16 | Input 4 | — |
| 17 | Input 5 | Injector 2 signal |
| 18 | KLINE | — |
| 19 | Input 11 | — |
| 20 | Input 10 | — |
| 21 | Input 9 | — |
| 22 | Input 8 | — |
| 23 | Input 7 | Injector 4 signal |
| 24 | VBAT1 | 12 V |
| 25 | HS123 | Injectors 1 and 5 positive |
| 26 | PWRGND | Ground |
| 27 | HS34 | — |
| 28 | HS456 | Injectors 2 and 3 positive |
| 29 | Input 6 | Injector 3 signal |
| 30 | Input 12 | — |
| 31 | HSABC | — |
| 32 | HS9A | — |
| 33 | PWRGND | Ground |
| 34 | HS789 | Injector 4 positive |
| 35 | VBAT2 | 12 V |
The manual repeats lambda-1 software labels and LSU pin numbers for its LAM2 section; confirm the second sensor wiring with Syvecs.