
Link G4X NGTTX is a vehicle-specific programmable plug-in ECU for the Nissan R34 GT-T application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NGTTX installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The NGTTX installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's NGTTX installation manual. Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Aux 5 is shared between pins 107 and 111 and its vehicle function differs; Link gives different tachometer duty cycles for RB20DE/RB25DE and RB25DET applications.
Factory main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| 101 | Injector 1 | Injection |
| 37 | nc | 4wd TPS Out (Not Connected) |
| 102 | nc | — |
| 38 | nc | — |
| 103 | Injector 3 | Injection |
| 39 | nc | — |
| 104 | Aux 1 | Intake Solenoid / WG Solenoid (R34 RB25DET) |
| 40 | nc | — |
| 105 | Injector 2 | Injection |
| 41 | nc | — |
| 106 | nc | — |
| 42 | nc | — |
| 107 | Aux 5 | Air Jet Swirl Solenoid (RB20DE Only) |
| 43 | Ground (Signal) | — |
| 108 | An Temp 4 | — |
| 44 | Trig 2 | Trig 2 |
| 109 | +12V constant | AC Clutch Relay Flywheeling |
| 45 | Trig 2 | Trig 2 |
| 110 | Injector 5 | Injection |
| 46 | Trig 1 | Trig 1 |
| 111 | Aux 5 | FP Speed (RB25DET Only) |
| 47 | An Volt 3 | Factory MAP Signal (RB25DET Only) |
| 112 | Injector 6 | Injection |
| 48 | +5V Out | — |
| 113 | nc | — |
| 49 | nc | — |
| 114 | Injector 4 | Injection |
| 50 | An Volt 2 | Oxy Signal |
| 115 | nc | — |
| 51 | nc | — |
| 116 | Ground | — |
| 52 | nc | — |
| 117 | Aux 6 | VTC Cam Solenoid |
| 53 | nc | — |
| 118 | Aux 7 | Oxy Heater |
| 54 | An Volt 1 | MAF Signal |
| 119 | nc | — |
| 55 | Ground (MAF) | — |
| 120 | nc | — |
| 56 | An Temp 1 | ECT |
| 121 | nc | — |
| 57 | nc | — |
| 122 | nc | — |
| 58 | nc | — |
| 123 | nc | — |
| 59 | nc | — |
| 124 | Ground | — |
| 60 | nc | — |
| 61 | nc | — |
| 1 | Ignition 1 | Ignition |
| 62 | Knock 2 | Knock |
| 2 | Ignition 5 | Ignition |
| 63 | Knock 1 | Knock |
| 3 | Ignition 3 | Ignition |
| 64 | nc | — |
| 4 | ECCS Relay Control | Pulls to ground when Ign is on |
| 65 | nc | — |
| 5 | Aux 3 | Tacho (20% Duty Cycle) |
| 66 | nc | — |
| 6 | — | — |
| 67 | +14V (Main Relay) | ECU Power |
| 7 | Ignition 6 | Ignition |
| 68 | nc | — |
| 8 | Ignition 2 | Ignition |
| 69 | nc | — |
| 9 | Ignition 4 | Ignition |
| 70 | nc | — |
| 10 | nc | — |
| 71 | nc | — |
| 11 | Aux 4 | ISC Solenoid |
| 72 | +14V (Main Relay) | ECU Power |
| 12 | nc | — |
| 73 | nc | — |
| 13 | Aux 2 | FP Relay |
| 74 | nc | — |
| 14 | Injector 7 (Aux) | A/C Clutch |
| 75 | nc | — |
| 15 | nc | — |
| 76 | nc | — |
| 16 | nc | — |
| 77 | nc | — |
| 17 | Aux 8 | CE Light |
| 78 | Injector 8 (Aux) | A/C Fan (RB25DE and RB25DET) |
| 18 | nc | — |
| 79 | nc | — |
| 19 | nc | — |
| 80 | nc (+12V constant) | — |
| 20 | DI 2 | Start Signal |
| 21 | DI 3 | A/C In |
| 22 | nc | — |
| 23 | An Volt 4 | TPS(Main) |
| 24 | Ignition Switch (+12V) | Used for Fan Flywheeling |
| 25 | Ground | — |
| 26 | DI 1 | Power Steer Switch |
| 27 | nc | — |
| 28 | nc | — |
| 29 | DI 4 | Vehicle Speed |
| 30 | nc | — |
| 31 | 12V Ignition Sw Input | Controls Pin 4 |
| 32 | nc | — |
| 33 | nc | — |
| 34 | nc | — |
| 35 | nc | — |
| 36 | nc | — |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Ground (Signal) | — |
| 2 | +5V Out | — |
| 3 | DI 5 | — |
| 4 | DI 6 | — |
| 5 | An Volt 5 | — |
| 6 | An Volt 6 | — |
| 7 | An Temp 2 | — |
| 8 | An Temp 3 | — |
| 9 | Ground (Signal) | — |
| 10 | +5V Out | — |
| 11 | DI 7 | — |
| 12 | DI 8 | — |
| 13 | An Volt 10 | — |
| 14 | An Volt 9 | — |
| 15 | Ignition 7 | — |
| 16 | Ignition 8 | — |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |