
Link G4X N300X is a vehicle-specific programmable plug-in ECU for the Nissan Z32 300ZX application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's N300X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The N300X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's N300X installation manual. Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. This schedule is identified as PCB V1.1 in the Link manual. Confirm the board version and exact vehicle before applying it.
Factory main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| 101 | Injector 1 | Injection |
| 31 | nc | — |
| 102 | nc | — |
| 32 | Aux 7 | CE Light |
| 103 | Injector 3 | Injection |
| 33 | nc | — |
| 104 | Aux 2 | Fuel Pump Control 1 |
| 34 | An Volt 5 | Power Steer Switch |
| 105 | Injector 5 | Injection |
| 35 | Aux 5 | Fuel Pump Control 2 |
| 106 | nc | — |
| 36 | An Temp 2 | Fuel Temp |
| 107 | Ground | — |
| 37 | nc | — |
| 108 | Ground | — |
| 38 | An Volt 3 | TPS |
| 109 | nc (+12V ECCS) | — |
| 39 | nc | — |
| 110 | Injector 2 | Injection |
| 40 | nc | — |
| 111 | nc | — |
| 41 | Trig 2 | Trig 2 |
| 112 | Injector 4 | Injection |
| 42 | Trig 1 | Trig 1 |
| 113 | Aux 8 | CAM Solenoids |
| 43 | DI 2 | Start Signal |
| 114 | Injector 6 | Injection |
| 44 | DI 4 | Neutral Switch |
| 115 | Ground (O2 Heater) | — |
| 45 | Ignition Switch | Control ECCS Relay output |
| 116 | Ground | — |
| 46 | DI 1 | A/C Request |
| 47 | nc | — |
| 1 | Ignition 1 | Ignition |
| 48 | + 5V | — |
| 2 | Ignition 2 | Ignition |
| 49 | +14V ECCS Relay | ECU Power |
| 3 | Ignition 3 | Ignition |
| 50 | Ground (Signal) | — |
| 4 | Aux 6 | ISC Solenoid |
| 51 | Trig 2 | Trig 2 |
| 5 | nc | — |
| 52 | Trig 1 | Trig 1 |
| 6 | Injector 8 (Aux) | Engine Fans |
| 53 | DI 3 | Vehicle Speed |
| 7 | Aux 4 | Tacho |
| 54 | nc | — |
| 8 | nc | — |
| 55 | An Volt 4 | Oxygen Sensor Bank 1 |
| 9 | Aux 3 | A/C Out |
| 56 | TPS Out | — |
| 10 | Ground | — |
| 57 | + 5V | — |
| 11 | Ignition 4 | Ignition |
| 58 | nc (+12V constant) | — |
| 12 | Ignition 5 | Ignition |
| 59 | +14V ECCS Relay | ECU Power |
| 13 | Ignition 6 | Ignition |
| 60 | Ground (Signal) | — |
| 14 | nc | — |
| 15 | nc | — |
| 16 | ECCS Relay Control | Pulls to ground when Ign is on |
| 17 | nc | — |
| 18 | Injector 7 (Aux) | Fuel Pump Relay |
| 19 | Injector 8 (Aux) | Engine Fans |
| 20 | Ground | — |
| 21 | nc | — |
| 22 | nc | — |
| 23 | Knock 1 | Knock |
| 24 | nc | — |
| 25 | Aux 1 | Wastegate Solenoid |
| 26 | Ground (AFM) | — |
| 27 | An Volt 2 | AFM Signal |
| 28 | An Temp 1 | ECT |
| 29 | An Volt 6 | Oxygen Sensor Bank 2 |
| 30 | Ground (Signal) | — |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Ground (Signal) | — |
| 2 | +5V Out | — |
| 3 | DI 5 | — |
| 4 | DI 6 | — |
| 5 | An Volt 8 | — |
| 6 | An Volt 7 | — |
| 7 | An Temp 3 | — |
| 8 | An Temp 4 | — |
| 9 | Ground (Signal) | — |
| 10 | +5V Out | — |
| 11 | Ignition 7 | — |
| 12 | Ignition 8 | — |
| 13 | DI 7 | — |
| 14 | DI 8 | — |
| 15 | An Volt 9 | — |
| 16 | An Volt 10 | — |
Internal sensor
| Position | Link ECU channel | Function |
|---|---|---|
| Internal MAP | An Volt 1 | MAP |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |