
SCS Delta GDI4 is a programmable SCS Delta engine-management controller. Legacy GDI4 direct-injection controller with AMPSeal A 776164-1 and B 776163-5. The documented hardware provides four paired high- and low-side injector connections, electronic throttle, pump control, knock inputs and additional PWM/relay outputs. SCS lists it as a legacy unit; do not substitute the GDI6 pinout. SXTune GDI4 hardware reference.
Pinout and connector identification
Connector B B1–B4 are injector 1–4 high side and B13–B16 injector 1–4 low side. B5–B6 are throttle motor, and B7–B8 are fuel-pump drive in the documented configuration. The complete GDI4 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune deltagdi4 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
The source repeats connector B in two tables with differing example application names at several positions, including B18–B20, B29 and B32. The table below reproduces the first source table's application column; those examples must not be treated as fixed configuration.
Connectors A and B
| Pin | Short Name | Name | Description | Application |
|---|---|---|---|---|
| A1 | VBATT | Battery | Power Supply input 6-18V | Direct Battery Supply (fuse 15A) |
| A2 | VKEY | Ignition | Ignition Switch input | Ignition Switched Supply (fuse 10A) |
| A3 | P_GND1 | Power Ground 1 | Power Ground | Power Ground 1 |
| A4 | OUT1 | Low Side 1 | 3A Open Collector w/recirc diode | Hot Soak Relay Control |
| A5 | OUT2 | Low Side 2 | 3A Open Collector w/recirc diode | A/C Clutch Relay Control |
| A6 | OUT3 | Low Side 3 | 3A Open Collector w/recirc diode | Purge Valve Control |
| A7 | OUT4 | Low Side 4 | 3A Open Collector w/recirc diode | Lambda Heater Drive |
| A8 | D_GND | Hall Ground | Digital Ground | Crank/Cam Sensors Ground |
| A9 | CRANK | Hall Input | Digital Input | Crank Sensor Input |
| A10 | CAM1 | Hall Input | Digital Input | Intake Cam Input |
| A11 | TCOOL | NTC Input | 3.16K pull-up to VREF | Coolant Temp Input |
| A12 | TAIR | NTC Input | 3.16K pull-up to VREF | Charge Air Temp Input |
| A13 | IGN1 | Ignition 1 | Logic or Power (hardware selected) | Ignition Coil 1 Output |
| A14 | IGN2 | Ignition 2 | Logic or Power (hardware selected) | Ignition Coil 2 Output |
| A15 | IGN3 | Ignition 3 | Logic or Power (hardware selected) | Ignition Coil 3 Output |
| A16 | IGN4 | Ignition 4 | Logic or Power (hardware selected) | Ignition Coil 4 Output |
| A17 | LINEAR1 | Analog Input 1 | 47k pull-up to VREF | Fuel Rail Pressure Input |
| A18 | CAM2 | Hall Input | Digital Input | Exhaust Cam Input |
| A19 | A_GND1 | Analog Ground 1 | Analog Ground | Temp Sensors Ground |
| A20 | LMBD1 | Lambda 1 Input | Weak bias to 450mV | Lambda 1 Input |
| A21 | CAN1H | CAN 1H | 120 Ohm Terminated | CAN 1 High |
| A22 | CAN1L | CAN 1L | CAN 1 Low | |
| A23 | HALL1 | Hall Input 1 | Digital Input | MAF Input |
| A24 | OUT5 | Low Side 5 | 3A Open Collector w/recirc diode | Main Relay Output |
| A25 | OUT6 | Low Side 6 | 3A Open Collector w/recirc diode | Thermostat Control Output |
| A26 | OUT7 | Low Side 7 | 3A Open Collector w/recirc diode | Intake Cam PWM Output |
| A27 | OUT8 | Low Side 8 | 3A Open Collector w/recirc diode | Exhaust Cam PWM Output |
| A28 | OUT9 | Low Side 9 | 3A Open Collector w/recirc diode | Fan 1 Relay/PWM Output |
| A29 | OUT10 | Low Side 10 | 3A Open Collector w/recirc diode | Fan 2 Relay/PWM Output |
| A30 | A_GND2 | Analog Ground 2 | Analog Ground | TPS/MAP/MAF Ground |
| A31 | NTC1 | NTC Input 1 | 3.16K pull-up to VREF | Gear Cut Input |
| A32 | LINEAR2 | Analog Input 2 | 47k pull-up to VREF | Throttle Position Sensor 1 Input |
| A33 | LINEAR3 | Analog Input 3 | 47k pull-up to VREF | MAP Sensor Input |
| A34 | VREF1 | VREF 1 | 5V 500mA sensor supply | 5V Sensor Supply 1 |
| A35 | P_GND2 | Power Ground 2 | Power Ground | Power Ground 2 |
| B1 | INJ1+ | Injector 1 + | Injector 1 High Side | Injector 1 + |
| B2 | INJ2+ | Injector 2 + | Injector 2 High Side | Injector 2 + |
| B3 | INJ3+ | Injector 3 + | Injector 3 High Side | Injector 3 + |
| B4 | INJ4+ | Injector 4 + | Injector 4 High Side | Injector 4 + |
| B5 | HBRIDGE1+ | H Bridge M+ | 5A H-Bridge | Throttle + |
| B6 | HBRIDGE1- | H Bridge M- | 5A H-Bridge | Throttle - |
| B7 | HBRIDGE2+ | Fuel Pump Drive + | 5A H-Bridge | Fuel Pump + |
| B8 | HBRIDGE2- | Fuel Pump Drive - | 5A H-Bridge | Fuel Pump - |
| B9 | OUT11 | Low Side 11 | 3A Open Collector w/recirc diode | Wastegate Valve Output |
| B10 | OUT12 | Low Side 12 | 3A Open Collector w/recirc diode | Recirc Valve Output |
| B11 | VREF2 | VREF 2 | 5V 500mA sensor supply | 5V Sensor Supply 2 |
| B12 | HBRIDGE3+ | H Bridge 3 M+ | 5A H-Bridge | Electronic Turbo Actuator + |
| B13 | INJ1- | Injector 1 - | Injector 1 Low Side | Injector 1 - |
| B14 | INJ2- | Injector 2 - | Injector 2 Low Side | Injector 2 - |
| B15 | INJ3- | Injector 3 - | Injector 3 Low Side | Injector 3 - |
| B16 | INJ4- | Injector 4 - | Injector 4 Low Side | Injector 4 - |
| B17 | HALL3 | Hall Input 3 | Digital Input | Wheel Speed Input LR |
| B18 | HALL4 | Hall Input 4 | Digital Input | Wheel Speed Input RR |
| B19 | HALL5 | Hall Input 5 | Digital Input | Wheel Speed Input LF |
| B20 | HALL6 | Hall Input 6 | Digital Input | Wheel Speed Input RF |
| B21 | KNOCK1 | Knock 1 + | Knock Input | Knock Sensor 1 Input |
| B22 | KNOCK2 | Knock 2 + | Knock Input | Knock Sensor 2 Input |
| B23 | K_GND | Knock Ground | Digital Ground | Knock Sensor Ground |
| B24 | HBRIDGE3- | H Bridge 3 M- | 5A H-Bridge | Electronic Turbo Actuator - |
| B25 | LINEAR4 | Analog Input 4 | 47k pull-up to VREF | Throttle Position Sensor 2 Input |
| B26 | LINEAR5 | Analog Input 5 | 47k pull-up to VREF | Pedal Position Sensor 1 Input |
| B27 | LINEAR6 | Analog Input 6 | 47k pull-up to VREF | Pedal Position Sensor 2 Input |
| B28 | LINEAR7 | Analog Input 7 | 47k pull-up to VREF | Oil Pressure Sensor Input |
| B29 | LINEAR8 | Analog Input 8 | 47k pull-up to VREF | Fuel Line Pressure Sensor Input |
| B30 | LINEAR9 | Analog Input 9 | 47k pull-up to VREF | Traction Control Pot Input |
| B31 | LINEAR10 | Analog Input 10 | 47k pull-up to VREF | A/C System Pressure Input |
| B32 | LINEAR11 | Analog Input 11 | 47k pull-up to VREF | Boost Pressure Sensor Input |
| B33 | NTC2 | NTC Input 2 | 3.16k pull-up to VREF | Fuel Level Input |
| B34 | CAN2H | CAN 2 H | 120 Ohm Terminated | CAN 2 High |
| B35 | CAN2L | CAN 2 L | CAN 2 Low |
PC communications DB9 female
| Pin | Name |
|---|---|
| 1 | Ground |
| 6 | CAN High |
| 7 | CAN Low |
| 8 | Battery Voltage |
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.