
Link G4X EVO8X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Evo IV–VIII application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's EVO8X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The EVO8X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
EVO8X factory header and expansion connector schedules
From Link’s EVOLink IV–VIII installation manual, pages 15–18. Link states the header is viewed into the ECU from the wire side. The model column describes Link’s example vehicle function; equipment differs across EVO versions. “nc” is reproduced from Link. Pin numbers 27–30, 47–50 and 63–70 are not listed in the source.
| Pin | Link channel | Vehicle function |
|---|---|---|
| 1 | Injector 1 | Injection |
| 2 | Injector 3 | Injection |
| 3 | nc | |
| 4 | Aux 5 | ISC stepper |
| 5 | Aux 7 | ISC stepper |
| 6 | nc | |
| 7 | nc | |
| 8 | Injector 5 | Fuel pump relay |
| 9 | nc | |
| 10 | Ignition 1 | Ignition cylinders 1 & 4 |
| 11 | Ignition 6 | Wastegate solenoid |
| 12 | +14 V Unreg | ECU power |
| 13 | Ground | |
| 14 | Injector 2 | Injection |
| 15 | Injector 4 | Injection |
| 16 | nc | |
| 17 | Aux 6 | ISC stepper |
| 18 | Aux 8 | ISC stepper |
| 19 | nc | |
| 20 | Ignition 4 (Aux) | Engine fan high speed (EVO 4–6 only) |
| 21 | Aux 1 | Engine fan low speed EVO 4–6; PWM EVO 7–8 |
| 22 | Ignition 3 (Aux) | A/C clutch |
| 23 | Ignition 2 | Ignition cylinders 2 & 3 |
| 24 | nc | |
| 25 | +14 V Unreg | ECU power |
| 26 | Ground | |
| 31 | nc | |
| 32 | Ignition 4 (Aux) | Engine fan high speed (EVO 4–6 only) |
| 33 | nc | |
| 34 | Ignition 4 (Aux) | Engine fan high speed (EVO 4–6 only) |
| 35 | Ignition 5 (Aux) | Wastegate solenoid |
| 36 | Injector 7 (Aux) | CE light |
| 37 | An Volt 5 | Power steering switch |
| 38 | Injector 8 (Aux) | ECU hold power (main relay) |
| 39 | Injector 6 (Aux) | Fuel pump speed relay |
| 40 | CAT Light | Jumper to ground for EVO 8 |
| 41 | nc | |
| 42 | nc | |
| 43 | nc | |
| 44 | DI 5 | Intercooler spray switch auto (EVO 7–8 only) |
| 45 | DI 6 | A/C request |
| 46 | nc | |
| 51 | nc | |
| 52 | nc | |
| 53 | nc | |
| 54 | nc | |
| 55 | EVO 4–7 ISC | Jumper to Aux 2 |
| 56 | nc | |
| 57 | EVO 8 ISC | Jumper to Aux 2 |
| 58 | Aux 3 | Tacho |
| 59 | nc | |
| 60 | Ground | Front O2 |
| 61 | nc | |
| 62 | nc | |
| 71 | DI 2 | Start signal |
| 72 | An Temp 2 | IAT (AFM) |
| 73 | An Volt 8 | MAP (factory sensor) |
| 74 | nc | |
| 75 | nc | |
| 76 | An Volt 4 | Oxygen signal |
| 77 | An Temp 3 | Fuel temperature (EVO 7–8) |
| 78 | Knock 1 | Knock |
| 79 | nc | |
| 80 | nc (+12 V constant) | |
| 81 | +5 V Out | |
| 82 | DI 1 | Ignition switch |
| 83 | An Temp 1 | ECT |
| 84 | An Volt 3 | TPS signal |
| 85 | nc | |
| 86 | DI 4 | Vehicle speed |
| 87 | nc | |
| 88 | Trig 2 | Trig 2 |
| 89 | Trig 1 | Trig 1 |
| 90 | An Volt 2 | AFM signal |
| 91 | DI 3 | Intercooler spray manual switch EVO 7–8 |
| 92 | Ground (signal) |
The source assigns Ignition 4 (Aux) to 20, 32 and 34 for the EVO 4–6 fan and describes certain fuel-pump and A/C outputs as swapped on some models; identify the vehicle and configure its base map. Injector 8 has hold-power hardware and is unsuitable for injector control without modification. An Volt 5 has a 4.7 kΩ pull-up and is not a regular analogue-voltage input. On-board MAP is An Volt 1.
Expansion connector
| Pin | Channel |
|---|---|
| 1 | Ground (signal) |
| 2 | +5 V Out |
| 3 | Aux 9 |
| 4 | Aux 10 |
| 5 | An Volt 6 |
| 6 | An Volt 7 |
| 7 | An Volt 9 |
| 8 | An Volt 10 |
| 9 | Ground (signal) |
| 10 | +5 V Out |
| 11 | DI 7 |
| 12 | DI 8 |
| 13 | DI 9 |
| 14 | DI 10 |
| 15 | Ignition 7 (Aux) |
| 16 | Ignition 8 (Aux) |
CAN 1 / RS232
| Pin | Function / wire colour |
|---|---|
| 1 | Comms GND (brown) |
| 2 | CAN1 L (green) |
| 3 | CAN1 H (white) |
| 4 | RS232 RX (grey) |
| 5 | RS232 TX (yellow) |
CAN 2 / OBD
| Pin | Function / wire colour |
|---|---|
| 1 | GND (brown) |
| 2 | CAN2 L (green) |
| 3 | CAN2 H (white) |
| 4 | NC (grey) |
| 5 | +14 V (yellow) |
Link cautions that connected serial wiring can interfere with USB when CAN 1/RS232 is used for CAN.