The Adaptronic eMod013 is an application-specific plug-in programmable engine-management ECU. Haltech's surviving Adaptronic downloads archive identifies the application as Mazda RX-8 Series 1. The part number identifies a family of applications, not an unconditional guarantee of vehicle compatibility. Haltech Adaptronic downloads archive.
Application and installation
Identify the vehicle, engine, connector and wiring variation before installation. Plug-in installation can still require additional sensor and actuator wiring, and tuning to suit the specific engine. The manufacturer archive provides the Adaptronic plug-in ECU startup guide and EUGENE tuning software.
Model-specific pinout
In the eMod013 section of the manufacturer download archive, find: RX8S1_Pinout_Rev2.zip. Open the matching vehicle-specific diagram; connector or pin functions cannot safely be inferred from a different eMod or a different application. The archive also lists the following basemap resource: emod013_RX8_S1_basemap.ecu.
Documentation limits
Complete channel counts and additional variants have not been independently verified for this exact model. Haltech's Adaptronic notice records the end of Adaptronic operations in 2022; use the archived documentation and confirm present support before purchasing a used ECU.
RX-8 Series 1 connector assignments and product photograph
Adaptronic's RX8S1 Rev2 sheet identifies the 2003–2008 RX-8 Series 1 and 13B-MSP and non-MSP Renesis engines. The connector view is looking into the ECU. It says the correct CAN setting must be chosen for the ABS module. Manufacturer pinout ZIP, preserved in Haltech's Adaptronic archive.
Adaptronic illustration, including product photograph, reproduced with permission. Open the image for the factory function, colour codes and manufacturer comments.
Incomplete source: The manufacturer sheet ends at 4Z and gives no connector 5 assignments although it illustrates connector 5. Some other positions are also not listed. Do not infer their function; 4C is labelled “None” in the Adaptronic column while its comment calls it +12 V DBW power, so confirm with the correct hardware documentation before connecting.
| Pin | Adaptronic function |
|---|---|
| 1A | CAS 3 |
| 1B | Drive-by-wire motor + (high to open) |
| 1C | Drive-by-wire motor − (low to open) |
| 1D | Digital input 12 (SSV switch) |
| 1E | Mod 3 (depends on installed module) |
| 1F | Sensor ground |
| 1G | Sensor ground |
| 1H | Mod 3 (depends on installed module) |
| 1J | TPS input 1 |
| 1K | Mod 3 (depends on installed module) |
| 1L | Injector output 7 (SSV) |
| 1M | TPS input 2 |
| 1N | Mod 3 (depends on installed module) |
| 1O | Ignition output 5 (air solenoid) |
| 1Q | TPS 5 V |
| 1R | Mod 3 (depends on installed module) |
| 1S | 5 V output (APV sensor) |
| 1T | Knock |
| 1U | Sensor ground |
| 1V | Power ground |
| 1W | Injector output 8 (VDI) |
| 1X | Mod 3 (depends on installed module) |
| 2A | Power ground |
| 2B | FRONTO2_H |
| 2C | FRONTO2_L |
| 2D | Injector output 6 (rear secondary) |
| 2E | Digital input 8 (oil pressure switch) |
| 2F | TPS ground |
| 2G | Injector output 5 (front secondary) |
| 2H | Sensor ground |
| 2I | Alternator control |
| 2J | Injector output 2 (rear primary 1) |
| 2K | Coolant temperature |
| 2M | Injector output 1 (front primary 1) |
| 2N | Digital input 3 (oil metering pump position switch) |
| 2O | Digital input 6 (neutral) |
| 2P | Auxiliary output 4 (purge) |
| 2Q | Oxygen input 2 |
| 2R | Digital input 7 (oil level switch) |
| 2T | External 0–5 V input 2 |
| 2U | CAS 1 (crank sensor +) |
| 2V | Additional output 5 (oil metering pump 1) |
| 2W | Additional output 6 (oil metering pump 2) |
| 2X | Sensor ground (crank sensor −) |
| 2Y | Additional output 7 (oil metering pump 1 inverse) |
| 2Z | Ignition output 2 (rear leading) |
| 2AA | Ignition output 1 (front leading) |
| 2AB | Additional output 8 (oil metering pump 2 inverse) |
| 2AC | Ignition output 4 (rear trailing) |
| 2AD | Ignition output 3 (front trailing) |
| 3A | Injector output 3 (front primary 2) |
| 3B | Servo (APV position sensor) |
| 3C | Mod 5 (depends on installed module) |
| 3D | Injector output 4 (rear primary 2) |
| 3E | Mod 5 (depends on installed module) |
| 3F | Mod 5 (depends on installed module) |
| 3G | Auxiliary output 1 (APV open) |
| 3H | Vehicle speed input |
| 3I | CAS 2 |
| 3J | Auxiliary output 2 (APV closed) |
| 3K | 5 V output |
| 3M | Sensor ground |
| 3N | Mod 5 (depends on installed module) |
| 3O | Oil pressure |
| 3P | Fuel pressure |
| 3Q | Oil temperature |
| 3R | Mod 5 (depends on installed module) |
| 4A | Power ground |
| 4B | Mod 5 (depends on installed module) |
| 4C | None (+12 V DBW power in comments) |
| 4D | NC |
| 4E | ECCS hardwired |
| 4F | Digital input 5 (clutch) |
| 4H | NC |
| 4I | Oxygen input 1 (aftermarket 0–5 V) |
| 4J | Power ground |
| 4K | 5 V output |
| 4L | NC |
| 4M | Ignition output 7 (fuel pump speed) |
| 4N | Tachometer |
| 4O | Ignition output 6 (air pump relay) |
| 4P | Digital input 10 (brake) |
| 4Q | Ignition switch |
| 4S | CAN L 1 |
| 4T | Digital input 9 (coolant level) |
| 4U | Sensor ground |
| 4V | CAN H 1 |
| 4W | Digital input 2 (A/C switch 1) |
| 4X | TPS 5 V (pedal power 2) |
| 4Y | TPS 5 V (pedal power 1) |
| 4Z | Digital input 1 (A/C switch 2) |
