
DTAFast T12+ is a programmable T-series engine ECU. Up to 12 cylinders fully sequential. Dual drive-by-wire, dual knock sensing, four variable cam controls and paddle-shift support. Manufacturer specification and product photographs.
Control and software
DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.
Connector pinout and wiring
Use the T12+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.
Complete connector pin assignments
These pin positions and labels are from the DTAFast T12-PLUS wiring diagram, shown from the pin-insertion side. A dash means no function is shown in the drawing. Verify the ECU version, electrical limits and configured functions before wiring.
Connector 1 — pinout version 1.03
| Pin | Function in manufacturer diagram |
|---|---|
| 1 | Coil 3 |
| 2 | Coil 11 |
| 3 | PWM 3 |
| 4 | PWM 2 |
| 5 | PWM 1 |
| 6 | Motor 1 + |
| 7 | Motor 1 - |
| 8 | Injector 11 |
| 9 | Injector 1 |
| 10 | Coil 1 |
| 11 | Coil 5 |
| 12 | Coil 7 |
| 13 | Power Ground 1 |
| 14 | Power Ground 2 |
| 15 | Injector 6 |
| 16 | Injector 5 |
| 17 | Injector 2 |
| 18 | Coil 2 |
| 19 | Coil 8 |
| 20 | Coil 9 |
| 21 | Injector 9 |
| 22 | Injector 10 |
| 23 | Injector 8 |
| 24 | Injector 7 |
| 25 | Injector 4 |
| 26 | Coil 4 |
| 27 | Coil 6 |
| 28 | Coil 10 |
| 29 | Motor 2 + |
| 30 | Motor 2 - |
| 31 | Ignition 12v In |
| 32 | Injector 12 |
| 33 | Coil 12 |
| 34 | Injector 3 |
Connector 2 — pinout version 1.03
| Pin | Function in manufacturer diagram |
|---|---|
| 1 | Analogue 2 |
| 2 | Wheel 1 |
| 3 | Analogue 10 |
| 4 | Digital 1 |
| 5 | Analogue 3 |
| 6 | Analogue 4 |
| 7 | Thermistor 1 |
| 8 | Digital 2 |
| 9 | 5v Output |
| 10 | Analogue 1 |
| 11 | Digital 3 |
| 12 | Crank Sensor |
| 13 | Analogue 12 |
| 14 | Digital 4 |
| 15 | Digital 5 |
| 16 | Analogue 11 |
| 17 | Thermistor 3 |
| 18 | Analogue 5 |
| 19 | Analogue 6 |
| 20 | Wheel 2 |
| 21 | Sensor Ground |
| 22 | Cam 1 |
| 23 | Cam 3 |
| 24 | 5v Output |
| 25 | Thermistor 2 |
| 26 | CAN High |
| 27 | Digital 6 |
| 28 | CAN Low |
| 29 | Cam 2 |
| 30 | Cam 4 |
| 31 | Wheel 3 |
| 32 | Wheel 4 |
| 33 | Sensor Ground |
| 34 | Analogue 9 |
Connector 3 — pinout version 1.03
| Pin | Function in manufacturer diagram |
|---|---|
| 1 | Lambda 2 Pump Current |
| 2 | Lambda 2 VGND |
| 3 | Lambda 2 Heater Negative |
| 4 | PWM 9 |
| 5 | Lambda 2 Trim Resistor |
| 6 | Lambda 2 Nernst Voltage |
| 7 | Lambda 1 Pump Current |
| 8 | Lambda 1 VGND |
| 9 | Lambda 1 Heater Negative |
| 10 | PWM 8 |
| 11 | Lambda 1 Trim Resistor |
| 12 | Lambda 1 Nernst Voltage |
| 13 | Analogue 13 |
| 14 | Analogue 14 |
| 15 | Analogue 15 |
| 16 | Analogue 16 |
| 17 | Analogue 7 |
| 18 | Analogue 8 |
| 19 | Digital 7 |
| 20 | Digital 8 |
| 21 | Digital 9 |
| 22 | PWM 4 |
| 23 | PWM 5 |
| 24 | PWM 6 |
| 25 | PWM 7 |
| 26 | Permanent 12v |
| 27 | Permanent 12v |
| 28 | PWM 10 |
| 29 | PWM 11 |
| 30 | PWM 12 |
| 31 | Knock 1 |
| 32 | Knock 2 |
| 33 | CAN 2 High |
| 34 | CAN 2 Low |
Identification
Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.