Tuning Wiki
Link G4X TST185X plug-in ECU
Manufacturer product image of TST185X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X TST185X is a vehicle-specific programmable plug-in ECU for the Toyota MR2 V1 and Celica ST185 application listed in Link's model-specific manuals index. It is an application board rather than a universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's TST185X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The TST185X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's TST185X installation manual (2025). Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Link’s guide covers Toyota MR2 V1 and Celica ST185. The separate multi-coil upgrade connector is listed below. On MR2, Link says the A/C request comes from the clutch rather than the push button. Injector drives 7 and 8 are not exposed.

Factory main header positions

Factory pinLink ECU channelFactory function
1 (B13)Ground—
44 (C11)An Volt 2TPS Signal
2 (B12)Injector 1Injection
45 (C10)An Temp 3Spare
3 (B11)Injector 2Injection
46 (C9)Ground (Signal)—
4 (B10)nc—
5 (B9)Aux 1ISC Open
51 (A11)DI 1Start Signal
6 (B8)Injector 6 (Aux)Oxy Heater
52 (A10)DI 2A/C Request
7 (B7)nc—
53 (A9)DI 3Vehicle Speed
8 (B6)Aux 3Wastegate Solenoid
54 (A8)nc—
9 (B5)nc—
55 (A7)nc—
10 (B4)nc—
56 (A6)Aux 4Fuel Pump Speed
11 (B3)nc—
57 (A5)Aux 8CE Light
12 (B2)nc—
58 (A4)nc—
13 (B1)Trig 1Trig 1 (NE)
59 (A3)nc—
14 (B26)Ground—
60 (A2)nc—
15 (B25)Injector 3Injection
61 (A1)nc (+12V constant)—
16 (B24)Injector 4Injection
62 (A22)nc—
17 (B23)Injector 5 (Aux)EGR
63 (A21)Aux 6—
18 (B22)Aux 2ISC Close
64 (A20)nc—
19 (B21)nc—
65 (A19)nc—
20 (B20)Ignition 1Ignition
66 (A18)nc—
21 (B19)nc—
67 (A17)nc—
22 (B18)Aux 5TVIS
68 (A16)nc—
23 (B17)Aux 7Fuel Pump Relay
69 (A15)nc—
24 (B16)nc—
70 (A14)nc—
25 (B15)Trig 2Trig 2 (G1)
71 (A13)+14VECU Power
26 (B14)Ground(Signal)—
72 (A12)+14VECU Power
31 (C8)nc—
32 (C7)nc—
33 (C6)An Volt 1Oxy Signal
34 (C5)Knock 1Knock
35 (C4)An Temp 1ECT
36 (C3)An Temp 2AFM IAT (ambient temp)
37 (C2)An Volt 4AFM
38 (C1)+5V Out—
39 (C16)Ground (G-)—
40 (C15)nc—
41 (C14)nc—
42 (C13)An Volt 3MAP (Factory Sensor)
43 (C12)nc—

Expansion connector

PinLink ECU channelFactory function
1Ground (Signal)—
2+5V Out—
3DI 5—
4DI 6—
5DI 4—
6An Volt 4—
7An Volt 5—
8An Volt 6—

Multi-coil upgrade plug

PinFunction
1Ignition 1
2Ignition 2
3Ignition 3
4Ignition 4

CAN 1/RS232 Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN1 LGreen
3CAN1 HWhite
4RS232-RXGrey
5RS232-TXYellow

Directly applicable articles

Technical articles assigned to this context will appear here.