
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW 135 335 N54 S7Plus, with product code S7plus-N54. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Confirmed installation details
The kit covers specified BMW 135 and 335 N54 applications. Its installation guide describes an ECU, adaptor harness and separate direct-injection driver; the supplied base calibration must match the engine's manifold pressure, turbocharger and fuel system configuration.
In the illustrated kit connector A, A2 and A3 are drive-by-wire H-bridge outputs and A4 is assigned to the DI pump. Follow the complete guide and confirm the hardware revision before using these examples.
Wiring and pinout
Syvecs BMW 135 335 N54 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs BMW 135 335 N54 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
N54 kit ECU and direct-injection driver pin schedules
From Syvecs N54 PNP manual, pages 5–7. These numbers identify the Syvecs ECU and separate DI driver connectors, not the original BMW connector. Empty cells mean the source gives no function. Check connector views, hardware and calibration; the DI driver and injector circuits are model-specific.
A — 34-way, key 1
| Pin | Syvecs I/O name | Application or source note |
|---|---|---|
| A1 | PWR CTR OUT | Main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | DI pump |
| A5 | H-Bridge4 / SlaveOut4 | VANOS intake low side |
| A6 | H-Bridge5 / SlaveOut5 | VANOS exhaust low side |
| A7 | H-Bridge6 / SlaveOut6 | Thermostat |
| A8 | H-Bridge7 / SlaveOut7 | Spare output |
| A9 | H-Bridge8 / SlaveOut8 | Spare output |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Primary injector 5 |
| A15 | FUEL6 | Primary injector 6 |
| A16 | FUEL7 | Port injector 1 / spare |
| A17 | FUEL8 | Port injector 2 / spare |
| A18 | PWM1 / *FUEL9 | Port injector 3 / spare |
| A19 | PWM2 / *FUEL10 | Engine fan 105 Hz |
| A20 | PWM3 / *FUEL11 | Port injector 4 / spare |
| A21 | PWM4 / *FUEL12 | Exhaust flap / port injector 5 |
| A22 | PWM5 | Fuel tank vent |
| A23 | PWM6 | Wastegate 1 |
| A24 | PWM7 | Wastegate 2 |
| A25 | PWM8 | Port injector 6 / spare |
| A26 | IGN1 | Ignition 1 |
| A27 | IGN2 | Ignition 2 |
| A28 | IGN3 | Ignition 3 |
| A29 | IGN4 | Ignition 4 |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | Ignition 6 |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
B — 26-way, key 1
| Pin | Syvecs I/O name | Application or source note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2L | — |
| B3 | CAN2H− | As labelled in source; confirm polarity |
| B4 | KNOCK | External loom |
| B5 | KNOCK 2 | External loom |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | LSU 4.9 connector pin 6 |
| B9 | LAM1B | LSU 4.9 connector pin 1 |
| B10 | LAM1C | LSU 4.9 connector pin 5 |
| B11 | LAM1D | LSU 4.9 connector pin 2 |
| B12 | LAM1HEATER | LSU 4.9 connector pin 3 |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | Source repeats LSU 4.9 pin 6; confirm with Syvecs |
| B15 | LAM2B | Source repeats LSU 4.9 pin 1; confirm with Syvecs |
| B16 | LAM2C | Source repeats LSU 4.9 pin 5; confirm with Syvecs |
| B17 | LAM2D | Source repeats LSU 4.9 pin 2; confirm with Syvecs |
| B18 | LAM2HEATER | Source repeats LSU 4.9 pin 3; confirm with Syvecs |
| B19 | IVBAT | 12 V |
| B20 | KLINE | Engine coolant pump and oil level |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
C — 34-way, key 2
| Pin | Syvecs I/O name | Application or source note |
|---|---|---|
| C1 | KNOCKGND | Knock ground |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | Powertrain CAN |
| C9 | CAN H | Powertrain CAN |
| C10 | AN01 | Direct injection pressure |
| C11 | AN02 | Crank position sensor |
| C12 | AN03 | Speed |
| C13 | AN04 | MAP sensor |
| C14 | AN05 | VVT1 intake |
| C15 | AN06 | VVT2 exhaust |
| C16 | AN07 | Spare input |
| C17 | AN08 | Spare input |
| C18 | AN09 | TPS1A |
| C19 | AN10 | TPS1B |
| C20 | AN11 | PPSA |
| C21 | AN12 | PPSB |
| C22 | AN13 | Intake air temperature |
| C23 | AN14 | Spare input |
| C24 | AN15 | Coolant temperature |
| C25 | AN16 | Oil pressure switch |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | 12 V ignition |
| C29 | AN S1 / Slave An01 | Brake light switch |
| C30 | AN S2 / Slave An02 | — |
| C31 | AN S3 / Slave An03 | Clutch switch |
| C32 | AN S4 / Slave An04 | Spare input |
| C33 | AN S5 / Slave An05 | Fuel pressure |
| C34 | AN S6 / Slave An06 | Barometric pressure |
Direct-injection driver — 35-way
| Pin | Syvecs I/O name | Application or source note |
|---|---|---|
| 1 | INJ1− | Injector 1 negative |
| 2 | INJ2− | Injector 2 negative |
| 3 | INJ3− | Injector 3 negative |
| 4 | — | — |
| 5 | INJ5− | Injector 5 negative |
| 6 | INJ6− | Injector 6 negative |
| 7 | — | — |
| 8 | INJ4− | Injector 4 negative |
| 9 | GND | Ground |
| 10 | INJ1_IN | Injector 1 control input |
| 11 | INJ2_IN | Injector 2 control input |
| 12 | — | — |
| 13 | INJ1+ | Injector 1 positive |
| 14 | INJ2+ | Injector 2 positive |
| 15 | INJ3+ | Injector 3 positive |
| 16 | — | — |
| 17 | INJ5+ | Injector 5 positive |
| 18 | INJ6+ | Injector 6 positive |
| 19 | — | — |
| 20 | INJ4+ | Injector 4 positive |
| 21 | GND | Ground |
| 22 | INJ3_IN | Injector 3 control input |
| 23 | — | — |
| 24 | GND | Ground |
| 25 | — | — |
| 26 | — | — |
| 27 | IGN | +12 V switched ignition |
| 28 | — | — |
| 29 | — | — |
| 30 | CAN H | CAN high |
| 31 | CAN L | CAN low |
| 32 | — | — |
| 33 | INJ4_IN | Injector 4 control input |
| 34 | INJ5_IN | Injector 5 control input |
| 35 | INJ6_IN | Injector 6 control input |
For B3 the manufacturer labels the channel “CAN2 H−”; confirm the polarity before connecting. B14–B18 repeat lambda-1 software labels and LSU pin numbers in the manual's second lambda section; confirm the actual lambda wiring with Syvecs. A5 and A6 are described as low-side VANOS assignments in this kit schedule.