Tuning Wiki

Adaptronic eSel042 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 4 (1985–1988) 13B single turbo. Adaptronic eSel042 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel042 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel042 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The assignments below are transcribed from that guide; verify the exact drawing and connector viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source repeats “left front” for both 1D and 1B in its wheel-speed comments; verify the intended position. Its direct-fire text repeats 1V in one sentence, while the coil list identifies 1V, 1X, 1U and 2O.

Factory pinFactory functionAdaptronic functionInstallation notes
3JWht / Blu Constant PowerConstant power in—
3IGrn / Yel Ignition Power+12V in—
3HLtGrn / Wht Secondary Injector 1Injector Output 2—
3GBlk GNDPower Ground—
3FLtGrn / Red Secondary Injector 2Injector Output 4—
3ELtGrn Primary Injector 1Injector Output 1—
3DBlk / Red Starter inhibitAux Output 5Fuel-pump modification needed if airflow meter is removed; see guide.
3CLtGrn / Blk Primary Injector 2Injector Output 3—
3BBlk / Blu Starter input——
3ABlk GNDPower Ground—
2RBlk GNDPower Ground—
2QBlu / Grn Idle ControlAux Output 2—
2PBlu / Yel Relief ValveDigital Input 6Factory output; available as ECU digital input.
2OBlu / Red Switching ValveIgnition Output 4Factory output; optional second-rotor leading ignition for four-coil conversion.
2NBlu / Wht EGR Valve——
2MBlu / Ora Pressure reg control valveAux Output 4Temporarily isolates regulator vacuum after starting.
2LGrn Manifold Air TempAir Temp Input (MAT)—
2KBlu / Blk Turbo Control ValveAux Output 3Boost control.
2JGrn / Ora Inlet Air TempAux Temp Input—
2IGrn / Wht Engine Coolant TempCoolant Temp Input—
2HGrn / Yel ATP——
2GGrn / Red TPS SignalTPS Input—
2FGrn / Blk Variable Resistor (tuning)MVSS InputOptional vehicle-speed input; factory ECU has none.
2EGrn / Blu Airflow SignalExt 0-5V InputAvailable 0–5 V input; not used for tuning.
2DGrey Oxygen Sensor SignalO2 Input—
2CBlk Sensor GroundSensor GND—
2BBrn / Red MAP SignalMAP InputOptional internal MAP sensor.
2ABrn / Wht 5V Sensor SupplyTPS +5V—
1XBlu / Yel Ignition TrailingIgnition Output 2180° firing interval.
1WBlk / Yel Heat HazardAux Output 6Dashboard indicator.
1VGrn / Yel Ignition LeadingIgnition Output 1180° firing interval.
1UBrn / Yel Ignition SelectIgnition Output 3Coil selection.
1TRed CAS: 24-tooth triggerCAS 2Other RX-7 plug-ins use CAS1 for multi-tooth trigger.
1SBrn / Red Port Air ValveAux Output 1Port air injection.
1RLtGrn Knock InputDigital Input 5Knock-module input.
1QWht CAS GroundSensor GND—
1PBlu CAS GroundSensor GND—
1OBlu / Blk Mileage sensorDigital Input 7Available digital input.
1NGrn CAS: 2-tooth triggerCAS 1Other RX-7 plug-ins use CAS2 for reset trigger.
1MBlu / Red Ignition Feedback——
1LYel / Blu Clutch SwitchDigital Input 1—
1KBlk / Red Shift LightAux Output 8—
1JOra Check ConnectorMVSS 2Four-wheel setup: right rear speed.
1IBlk / Blu "Overtop" (overdrive)Digital Input 3—
1HBrn Water Temp SwitchKnockMay accept a direct knock sensor.
1GGrn / Blk Neutral SwitchDigital Input 2—
1FBlu / Wht Air Conditioner ClutchAux Output 7—
1EBlu / Ora Air Conditioner RequestDigital Input 4—
1DYel Check ConnectorSVSS1Four-wheel setup: left front speed, per source.
1CBrn / Yel Air Bypass——
1BYel / Red Check ConnectorSVSS2Four-wheel setup: left front speed, per source; duplicate with 1D.
1AYel / Blk Check ConnectorCAS3Optional flex-fuel input.

Select family illustration

Adaptronic eSel040 Select ECU family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel042 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.

Directly applicable articles

Technical articles assigned to this context will appear here.