Tuning Wiki

Engine-management systems need a way to relate the engine's operating conditions to the fuel and ignition calibration. Manifold pressure, throttle position and measured air mass are different inputs to that process. The choice of table axis is not necessarily the same as the complete air-charge calculation: individual ECUs combine inputs and corrections in different ways.

Pressure-based load and speed density

A pressure-based table commonly uses manifold absolute pressure (MAP) and engine speed. In a speed-density fuel model, pressure and intake temperature help estimate air density; a calibrated efficiency value relates the available volume to the air entering the cylinders. For example, MoTeC describes an engine-load calculation using engine efficiency, displacement, cylinder count, manifold pressure and manifold temperature. MoTeC: engine efficiency and load model

MAP is absolute pressure: an engine stopped with the ignition on should normally read approximately local atmospheric pressure, not zero. Compare like units and pressure references when diagnosing a sensor. Sensor plumbing, calibration and the ECU's temperature measurement affect the model.

Pressure signal and response

Use the pressure source and hose arrangement specified for the engine and ECU, and check hoses and connections for leaks or obstruction. Individual runners can produce strong pulses, so some installations combine or damp their pressure signals; damping must be assessed against response during rapid throttle changes. There is no universal accumulator size for every engine. Individual throttle bodies describes the alternatives.

Hose length, filtering and the ECU's sampling strategy can affect how quickly the displayed value follows a change. Haltech notes that shorter sensor plumbing can reduce delay in its transient-throttle guidance. Its manifold-pressure documentation also describes filtering and a hose-failure diagnostic for a supported system. Those features and settings are ECU-specific. Compare pressure and throttle traces during representative transients rather than judging the signal at idle alone.

Throttle-based load (Alpha-N)

Alpha-N uses throttle position and engine speed as primary table coordinates. It can provide useful resolution when manifold pressure is highly pulsating or changes little over much of the useful throttle range. Throttle angle by itself does not directly measure the mass of air entering the engine. Changes in atmospheric pressure, temperature or boost may require additional measurements and corrections, depending on the ECU and installation.

The same controller can still use a MAP sensor for other functions even when the primary table is throttle based. MoTeC's M84 documentation gives specific MAP and throttle arrangements for its own system; these should not be assumed to apply to every ECU. MoTeC M84 user manual: load sensing

MAF and combined strategies

A mass-airflow sensor measures air passing the sensor, rather than using throttle angle as a proxy. Its signal still needs the correct sensor transfer calibration, and measured intake flow does not necessarily equal cylinder flow instantaneously during rapid transients. Some systems use more than one air-charge model, sensor or efficiency table; their blending, backup and fault behaviour are firmware-specific. MoTeC documents an example with both throttle- and manifold-pressure-based efficiency tables. MoTeC GPR Motorcycle: engine efficiency tables

Range and protection on boosted engines

A pressure sensor and its ECU calibration need to represent the full expected operating range, including positive manifold pressure. If the signal reaches its measurement limit, the ECU cannot distinguish a further pressure increase from the highest indicated value. Verify the sensor range, electrical transfer and calibration for the actual system. Haltech lists different sensor ranges for different engine configurations. Haltech: MAP sensor ranges.

Overboost detection is a separate protective function, with behaviour that depends on the ECU's setup. Haltech documents pressure, delay, hysteresis and cut-method parameters for one implementation. A clamp or disconnected sensor can prevent the ECU from seeing the true condition and can affect fuel, ignition and protection calculations; investigate the cause instead of masking the measurement. Haltech: overboost protection.

Camshaft overlap and signal quality

Valve overlap is the period around the exhaust-to-intake transition when both valves are open. Cam timing and overlap can change idle vacuum, charge dilution and airflow behaviour, so a camshaft change can alter the relationship the previous calibration assumed. COMP Cams discusses overlap and its effects on vacuum and response in its valve-timing tutorial; the result depends on the complete engine and cam timing.

Low or pulsating manifold pressure can reduce the useful separation between operating points in a MAP-based table. Throttle position may offer useful resolution in some installations, but it does not directly measure trapped air mass and may need other compensation. Holley discusses the trade-off for its Hilborn EFI examples. Check the chosen controller’s supported load model and compare logged signals before changing strategy; a camshaft specification alone does not dictate one universal solution.

Choosing and checking a strategy

  1. Identify the ECU, firmware and supported fuel models; read the instructions for how each table axis, compensation and sensor input is used.
  2. Inspect the intake arrangement and log stable MAP and throttle readings over the usable range. Choose a strategy that gives useful resolution with the actual sensors and installation.
  3. Verify sensor calibration and plausibility, injector data, ignition timing and fuel pressure before adjusting the fuel model. Do not treat a change in load strategy as a conversion of an existing tune; its values and corrections may no longer have the same meaning.
  4. Validate the new calibration progressively with a suitable wideband and controlled load. Monitor engine temperature, fuel pressure and abnormal combustion, and reduce load if conditions become unsafe. Haltech: applying load to the engine

See also Standalone ECU fuel tuning guide, Airflow sensors and Individual throttle bodies.