
SCS Delta GDI6 is a programmable SCS Delta engine-management controller. GDI6 is a direct-injection controller with three 35-way AMPSeal connectors, including a blue GDI connector. Its documented assignments include six paired GDI injector high- and low-side outputs, throttle motor and high-pressure pump bridges. SCS lists it for a Ford 2.0 GDI package; that kit is an application-specific calibration. SXTune GDI6 hardware reference.
Pinout and connector identification
Connector B B1–B6 are GDI injector 1–6 high side and B13–B18 injector 1–6 low side. B7/B8 are throttle motor control, B9/B10 are high-pressure pump 1 and B11/B12 are high-pressure pump 2 connections; use the complete diagram for polarity and conditions. The complete GDI6 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune deltagdi6 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
The source names both B11 and B12 “H Bridge 3 M−” while describing pump 2 positive and negative respectively. This inconsistency is reproduced below; confirm polarity with SCS before wiring.
Connector A — AMPSeal 776231-1 (black)
| Pin | Name | Description | Notes |
|---|---|---|---|
| 1 | Battery Direct | Battery Supply (15A fuse) | Direct Battery Power 6-15V |
| 2 | Ignition | Ignition Switched Supply (10A fuse) | Ignition Key Input |
| 3 | Power Ground 1 | Power Ground | Power Ground 1 |
| 4 | Low Side Output 1 | 1.5A Open Collector | Port Injector 1 Output |
| 5 | Low Side Output 2 | 1.5A Open Collector | Port Injector 2 Output |
| 6 | Low Side Output 3 | 1.5A Open Collector | Port Injector 3 Output |
| 7 | Low Side Output 4 | 1.5A Open Collector | Port Injector 4 Output |
| 8 | Crank/Cam Ground | Digital Ground | Crank/Cam Sensor Ground |
| 9 | Crank Input | VR/Hall - Software Selectable | Crank Sensor Input |
| 10 | Cam Input 1 | VR/Hall - Software Selectable | Cam Sensor 1 Input |
| 11 | Coolant Temp Input | 3.16K pull-up to VREF | Coolant Temperature Input |
| 12 | Air Temp Input | 3.16K pull-up to VREF | Air Temperature Input |
| 13 | Ignition 1 | TTL/Power Ignition Output | Software Configurable Ignition Output |
| 14 | Ignition 2 | TTL/Power Ignition Output | Software Configurable Ignition Output |
| 15 | Ignition 3 | TTL/Power Ignition Output | Software Configurable Ignition Output |
| 16 | Ignition 4 | TTL/Power Ignition Output | Software Configurable Ignition Output |
| 17 | Analog Input 1 | 47k pull-up to VREF | Linear 1 Input |
| 18 | Cam Input 2 | VR/Hall - Software Selectable | Cam Sensor 2 Input |
| 19 | Analog Ground 1 | Analog Ground | Analog Ground |
| 20 | Lambda 1 Input | Weak bias to 450mV | Narrowband Lambda Sensor 1 Input |
| 21 | CAN 1H | To PC comms DTM | CAN High |
| 22 | CAN 1L | To PC comms DTM | CAN Low |
| 23 | Low Side Output 5 | 1.5A Open Collector | Auxiliary 1 / Port Injector 5 Output |
| 24 | Low Side Output 7 | 1.5A Open Collector w/ recirc diode | Relay 1 / Main Relay Output |
| 25 | Low Side Output 8 | 1.5A Open Collector w/ recirc diode | Relay 2 / Fuel Pump Relay Output |
| 26 | Low Side Output 9 | 1.7A Open Collector w/ recirc diode | PWM 1 Output |
| 27 | Low Side Output 10 | 1.7A Open Collector w/ recirc diode | PWM 2 Output |
| 28 | Low Side Output 11 | 0.75A Open Collector w/ recirc diode | Relay 3 Output |
| 29 | Low Side Output 6 | 1.5A Open Collector | Auxiliary 2 / Port Injector 6 Output |
| 30 | Analog Ground 2 | Analog Ground | Analog Sensors Ground |
| 31 | NTC Input 1 | 3.16K pull-up to VREF | NTC1 Input |
| 32 | Analog Input 2 | 47k pull-up to VREF | Throttle Position Sensor Input |
| 33 | Analog Input 3 | 47k pull-up to VREF | Manifold Pressure Sensor Input |
| 34 | VREF | 200mA 5V supply to sensors | 5V Reference Sensor Supply |
| 35 | Power Ground 2 | Power Ground | Power Ground 2 |
Connector B — AMPSeal 776231-5 (blue)
| Pin | Name | Description | Notes |
|---|---|---|---|
| B1 | INJ1+ | Injector 1 High Side | GDI Injector High-Side Bank 1 |
| B2 | INJ2+ | Injector 2 High Side | GDI Injector High-Side Bank 1 |
| B3 | INJ3+ | Injector 3 High Side | GDI Injector High-Side Bank 1 |
| B4 | INJ4+ | Injector 4 High Side | GDI Injector High-Side Bank 2 |
| B5 | INJ5+ | Injector 5 High Side | GDI Injector High-Side Bank 2 |
| B6 | INJ6+ | Injector 6 High Side | GDI Injector High-Side Bank 2 |
| B7 | H Bridge 1 M+ | 8.6A H-Bridge Output | Throttle Motor Control + |
| B8 | H Bridge 1 M- | 8.6A H-Bridge Output | Throttle Motor Control - |
| B9 | H Bridge 2 M+ | 8.6A H-Bridge Output | High Pressure Pump 1 + |
| B10 | H Bridge 2 M- | 8.6A H-Bridge Output | High Pressure Pump 1 - |
| B11 | H Bridge 3 M- | 8.6A H-Bridge Output | High Pressure Pump 2 + |
| B12 | H Bridge 3 M- | 8.6A H-Bridge Output | High Pressure Pump 2 - |
| B13 | INJ1- | Injector 1 Low Side | GDI Injector #1 Low-Side |
| B14 | INJ2- | Injector 2 Low Side | GDI Injector #2 Low-Side |
| B15 | INJ3- | Injector 3 Low Side | GDI Injector #3 Low-Side |
| B16 | INJ4- | Injector 4 Low Side | GDI Injector #4 Low-Side |
| B17 | INJ5- | Injector 5 Low Side | GDI Injector #5 Low-Side |
| B18 | INJ6- | Injector 6 Low Side | GDI Injector #6 Low-Side |
| B19 | Ignition 5 | TTL/Power Ignition Output | Software Configurable Ignition Output |
| B20 | Ignition 6 | TTL/Power Ignition Output | Software Configurable Ignition Output |
| B21 | Knock 1 + | Knock 1 Signal Input | Knock Sensor Input |
| B22 | Knock 2 + | Knock 2 Signal Input | Knock Sensor Input |
| B23 | Knock Ground | Digital Ground | Knock Sensors Ground |
| B24 | Lambda 2 Input | Weak bias to 450mV | Narrowband Lambda 2 Input |
| B25 | Analog Input 4 | 47k pull-up to VREF | Throttle Position Sensor 2 Input |
| B26 | Analog Input 5 | 47k pull-up to VREF | Pedal Position Sensor 1 Input |
| B27 | Analog Input 6 | 47k pull-up to VREF | Pedal Position Sensor 2 Input |
| B28 | NTC Input 2 | 3.16k pull-up to VREF | NTC 2 Input |
| B29 | NTC Input 3 | 3.16k pull-up to VREF | NTC 3 Input |
| B30 | Analog Input 7 | 47k pull-up to VREF | Linear 5 Input |
| B31 | Analog Input 8 | 47k pull-up to VREF | Linear 6 Input |
| B32 | Analog Input 9 | 47k pull-up to VREF | Linear 7 Input |
| B33 | Analog Input 10 | 47k pull-up to VREF | Linear 8 Input |
| B34 | CAN 2L | CAN bus 2 Low | |
| B35 | CAN 2H | CAN bus 2 High |
Connector C — AMPSeal 776231-2 (white)
| Pin | Name | Description | Notes |
|---|---|---|---|
| C1 | Wideband Lambda 1 Heater | 1.7A Open collector with recirc diode | Wideband Lambda Sensor 1 Heater |
| C2 | Wideband Lambda 1 Ip | Wideband Lambda Sensor 1 Ip | |
| C3 | Wideband Lambda 1 Ia | Wideband Lambda Sensor 1 Ia | |
| C4 | Wideband Lambda 1 Vm | Wideband Lambda Sensor 1 Vm | |
| C5 | Wideband Lambda 1 Nernst | Wideband Lambda Sensor 1 Un | |
| C6 | Cam Input 3 | VR/Hall - Software Selectable | Cam Sensor 3 Input |
| C7 | Cam Input 4 | VR/Hall - Software Selectable | Cam Sensor 4 Input |
| C8 | LIN | LIN communications | |
| C9 | Hall Input1 | Hall Effect Input (2k7 Pull-up to 5V) | Left Rear Wheel Speed Input |
| C10 | Hall Input2 | Hall Effect Input (2k7 Pull-up to 5V) | Right Rear Wheel Speed Input |
| C11 | Hall Input3 | Hall Effect Input (2k7 Pull-up to 5V) | Left Front Wheel Speed Input |
| C12 | Hall Input4 | Hall Effect Input (2k7 Pull-up to 5V) | Right Front Wheel Speed Input |
| C13 | Wideband Lambda 2 Heater | 1.7A Open collector with recirc diode | Wideband Lambda Sensor 2 Heater |
| C14 | Wideband Lambda 2 Ip | Wideband Lambda Sensor 2 Ip | |
| C15 | Wideband Lambda 2 Ia | Wideband Lambda Sensor 2 Ia | |
| C16 | Wideband Lambda 2 Vm | Wideband Lambda Sensor 2 Vm | |
| C17 | Wideband Lambda 2 Nernst | Wideband Lambda Sensor 2 Un | |
| C18 | Low Side Output 12 | 1.7A Open collector with recirc diode | Auxiliary 3 Output |
| C19 | Low Side Output 13 | 1.7A Open collector with recirc diode | Auxiliary 4 Output |
| C20 | Bipolar Output 1 | 2.5A Hi Side/Lo Side Drive | PWM 5 Bipolar output |
| C21 | Bipolar Output 2 | 2.5A Hi Side/Lo Side Drive | PWM 6 Bipolar output |
| C22 | Bipolar Output 3 | 2.5A Hi Side/Lo Side Drive | PWM 7 Bipolar output |
| C23 | Bipolar Output 4 | 2.5A Hi Side/Lo Side Drive | PWM 8 Bipolar output |
| C24 | Low Side Output 14 | 1.5A Open collector with recirc diode | HEGO Heater 1 |
| C25 | Low Side Output 15 | 1.5A Open collector with recirc diode | HEGO Heater 2 |
| C26 | Low Side Output 16 | 1.5A Open collector with recirc diode | Relay 4 Output |
| C27 | Low Side Output 17 | 1.5A Open collector with recirc diode | Relay 5 Output |
| C28 | Low Side Output 18 | 0.75A Open collector with recirc diode | Relay 6 Output |
| C29 | Low Side Output 19 | 0.75A Open collector with recirc diode | Relay 7 Output |
| C30 | Hall Input 5 | Hall Effect Input (2k7 Pull-up to 5V) | SENT Position Sensor Input |
| C31 | Analog Input 11 | 47k pull-up to VREF | Linear 9 Input |
| C32 | Analog Input 12 | 47k pull-up to VREF | Linear 10 Input |
| C33 | NTC Input 4 | 3.16k pull-up to VREF | NTC 4 Input |
| C34 | VREF2 | 200mA 5V supply to sensors | 5V Reference Sensor Supply |
| C35 | Analog Ground 2 | Analog Ground | Analog Sensors Ground |
DTM PC communications connector
| Pin | Name | Description | Notes |
|---|---|---|---|
| 1 | Battery Voltage | ||
| 2 | Ground | ||
| 3 | CAN High | ||
| 4 | CAN Low |
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.