Link WRX6X G4X plug-in ECU for Subaru WRX version 5–6, with installation and pinout reference.
Published
Manufacturer product image of WRX6X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X WRX6X is a vehicle-specific programmable plug-in ECU for the Subaru WRX version 5–6 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX6X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The WRX6X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's WRX6X installation manual (2025). Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Applies to the V5–6 WRX/STi layouts documented by Link. The E-throttle connector is absent on bottom boards before V1.4; the CAN connectors also differ by board revision. Some version 6 vehicles need the Subaru V7–8 MAP calibration, according to Link. Injector drives 7 and 8 are not exposed.
Factory main header positions
Factory pin
Link ECU channel
Factory function
B134-1
Aux 1
Fuel Pump Relay
B135-30
nc
—
B134-2
nc
—
B135-31
nc
—
B134-3
nc
—
B135-32
nc
—
B134-4
Ignition 3 (Aux)
Fan Relay 1
B134-5
Aux 6
Idle Stepper Motor
B136-1
An Volt 2
AFM Signal
B134-6
Aux 5
Idle Stepper Motor
B136-2
nc
—
B134-7
Ignition 1
Ignition
B136-3
nc
—
B134-8
Ground
—
B136-4
nc
—
B134-9
Ground
—
B136-5
Trig 1 / Trig 2
via dip switch
B134-10
nc
—
B136-6
Trig 2 / Trig 1
via dip switch
B134-11
nc
—
B136-7
An Volt 1
Factory MAP Sensor
B134-12
nc
—
B136-8
+14V Main Relay
ECU Power
B134-13
Ignition 4 (Aux)
Fan Relay 2
B136-9
+14V Main Relay
ECU Power
B134-14
Aux 7
Idle Stepper Motor
B136-10
nc
—
B134-15
Aux 8
Idle Stepper Motor
B136-11
nc
—
B134-16
Ignition 2
Ignition
B136-12
+5V Out
—
B134-17
Ground
—
B136-13
nc
—
B134-18
Injector 4
Injection
B136-14
nc
—
B134-19
Aux 2
Wastegate Solenoid
B136-15
nc
—
B134-20
nc
—
B136-16
nc
—
B134-21
Aux 1
Fuel Pump Relay
B136-17
Ground
—
B134-22
Aux 3
A/C Out
B136-18
Ground
—
B134-23
nc
—
B136-19
An Temp 3
Spare
B134-24
nc
—
B136-20
An Volt 3
TPS (Main)
B134-25
Injector 3
Injection
B136-21
An Volt 4
Oxygen Sensor Signal
B134-26
nc
—
B136-22
nc
—
B134-27
nc
—
B136-23
Ground (Triggers)
—
B134-28
Injector 5 (Aux)
CE Light
B136-24
Ground (Signal)
—
B134-29
nc
—
B136-25
DI 4
Ignition Switch
B134-30
nc
—
B136-26
Knock 1
Knock
B134-31
Injector 1
Injection
B136-27
nc
—
B134-32
Injector 2
Injection
B136-28
An Temp 1
ECT
B136-29
Ground (Knock Shield)
—
B135-1
DI 2
Power Steer Signal
B136-30
Ground (Signal)
—
B135-2
DI 1
Start Signal
B136-31
Ground (MAF)
—
B135-3
nc
—
B136-32
Injector 6 (Aux)
ECU Hold Power
B135-4
nc
—
B135-5
nc
—
B135-6
nc
—
B135-7
nc
—
B135-8
nc
—
B135-9
nc
—
B135-10
nc
—
B135-11
DI 6
A/C In
B135-12
nc
—
B135-13
nc
—
B135-14
Aux 4
Tacho
B135-15
nc
—
B135-16
nc
—
B135-17
nc
—
B135-18
nc
—
B135-19
nc
—
B135-20
nc
—
B135-21
nc
—
B135-22
nc
—
B135-23
nc
—
B135-24
nc
—
B135-25
nc
—
B135-26
DI 3
Vehicle Speed
B135-27
nc
—
B135-28
nc
—
B135-29
nc
—
Expansion connector
Pin
Link ECU channel
Factory function
1
Ground (Signal)
—
2
+5V Out
—
3
DI 5
—
4
DI 7
—
5
An Volt 5
—
6
An Volt 6
—
7
An Temp 2
—
8
An Temp 3
—
9
Ground (Signal)
—
10
+5V Out
—
11
DI 8
—
12
DI 9
—
13
An Volt 8
—
14
An Volt 9
—
15
Ignition 7 (Aux)
—
16
Ignition 8 (Aux)
—
E-throttle connector: bottom board V1.4 onwards
Pin
Function
Notes
1
Ground (Signal)
—
2
+5V Out
—
3
An Volt 11
—
4
An Volt 10
—
5
An Volt 7
—
6
nc
—
7
Aux 10
—
8
Aux 9
—
CAN 1/RS232, before V1.4
Pin
Function
Wire colour
1
Comms GND
Brown
2
CAN1 L
Green
3
CAN1 H
White
4
RS232-RX
Grey
5
RS232-TX
Yellow
CAN 2/OBD, before V1.4
Pin
Function
Wire colour
1
GND
Brown
2
CAN2 L
Green
3
CAN2 H
White
4
NC
Grey
5
+14V
Yellow
Four-pin CAN 1 and 2, V1.4 onwards
Pin
Function
Wire colour
1
GND
Black
2
CAN L
Green
3
CAN H
White
4
+14V
Red
Additional CAN 1/RS232, V1.4 onwards
Pin
Function
Wire colour
1
Comms GND
Brown
2
CAN1 L
Green
3
CAN1 H
White
4
RS232-RX
Grey
5
RS232-TX
Yellow
Directly applicable articles
Technical articles assigned to this context will appear here.