
GEMS GDi80: A four-cylinder direct-injection ECU with integrated direct-injector and high-pressure-pump drivers. Manufacturer source.
Hardware and control
The rev 16 datasheet identifies four direct injection drivers, four port injection drivers, four active-coil signals, a high-pressure pump drive, electronic-throttle bridges, wideband lambda, two CAN buses and 256 MB logging. It uses an 80-position, two-plug arrangement; the DI and port outputs are not interchangeable. GEMS model information.
GEMS systems use GWv4 configuration, with the required ECU definition and licence; software options and custom builds can differ. Record the label, hardware and firmware and confirm connected devices against the matching documentation. GWv4 manual.
Connector 1 pinout — 103355 rev 16
The manufacturer technical specification identifies connector 1 as the 32-position mating connector; use its drawing and cavity markings for orientation, verify current limits and shared input functions. These positions apply only to this specific model and document revision.
| Pin | Function in source |
|---|---|
| A1 | Knock input + |
| B1 | Knock input − |
| C1 | Active throttle feedback 2 |
| D1 | Active throttle feedback 1 |
| E1 | MAF input |
| F1 | Coolant temperature input |
| G1 | Active throttle bridge A+ |
| H1 | Main 12 V supply |
| A2 | CAN 2 low |
| B2 | CAN 2 high |
| C2 | Active throttle feedback 3 |
| D2 | Active throttle feedback 4 |
| E2 | 5 V sensor supply 1 |
| F2 | Sensor ground |
| G2 | Active throttle bridge A− |
| H2 | Main 12 V supply |
| A3 | CAN 1 low |
| B3 | CAN 1 high |
| C3 | MAP input |
| D3 | Narrowband lambda input 1 |
| E3 | Narrowband lambda input 2 |
| F3 | Sensor ground |
| G3 | High-pressure pump drive + |
| H3 | High-pressure pump drive − |
| A4 | Ethernet RX− |
| B4 | Ethernet RX+ |
| C4 | Ethernet TX− |
| D4 | Ethernet TX+ |
| E4 | Analogue input 17 |
| F4 | Analogue input 27 |
| G4 | Power return |
| H4 | Power return |
Connector 2 pinout — 103355 rev 16
Based on the GDi80 rev 16 technical specification. The source labels direct-injector pairs separately from their cylinder/Fuel assignments, assuming firing order 1-3-4-2. Follow its original notes, configuration, connector orientation and high-voltage driver instructions for the exact hardware.
| Pin | Function in source |
|---|---|
| A1 | PWM driver 3 |
| B1 | PWM driver 4 |
| C1 | Bridge D− |
| D1 | Bridge D+ |
| E1 | Bridge C− |
| F1 | Bridge C+ |
| G1 | PWM low-side driver / analogue input A30 |
| H1 | PWM low-side driver / analogue input A28 |
| J1 | PWM low-side driver / analogue input A26 |
| K1 | PWM low-side driver / analogue input A2 |
| L1 | Direct injector 1− |
| M1 | Direct injector 2− |
| A2 | Sensor ground |
| B2 | Air inlet temperature input |
| C2 | Accelerator pedal input 1 |
| D2 | Accelerator pedal input 2 |
| E2 | Timing input 1 |
| F2 | Timing input 2 |
| G2 | Timing input 3 |
| H2 | Timing input 4 |
| J2 | Secondary 12 V supply |
| K2 | Wideband lambda heater |
| L2 | Direct injector 1+ |
| M2 | Direct injector 2+ |
| A3 | 5 V sensor supply 3 |
| B3 | Timing input 12 |
| C3 | Timing input 11 |
| D3 | Timing input 10 |
| E3 | Timing input 9 |
| F3 | Timing ground |
| G3 | Wideband lambda 1 |
| H3 | Wideband lambda 2 |
| J3 | Wideband lambda 3 |
| K3 | Wideband lambda 4 |
| L3 | Direct injector 3+ |
| M3 | Direct injector 4+ |
| A4 | Bridge driver B− |
| B4 | Bridge driver B+ |
| C4 | Port injector Fuel8 |
| D4 | Port injector Fuel7 |
| E4 | Port injector Fuel6 |
| F4 | Port injector Fuel5 |
| G4 | Ignition coil drive cylinder 3 |
| H4 | Ignition coil drive cylinder 4 |
| J4 | Ignition coil drive cylinder 2 |
| K4 | Ignition coil drive cylinder 1 |
| L4 | Direct injector 3− |
| M4 | Direct injector 4− |
Functions may be shared or configurable; verify current limits and calibration in the complete datasheet.
Further references
- GEMS GDi80 manufacturer source
- Model-specific technical and wiring specification
- GEMS software and downloads
- GEMS manufacturer overview
Sources reviewed 17 November 2026.