
SCS Delta 700 is a programmable SCS Delta engine-management controller. A two-connector unit with 35-way A and B AMPSeal connectors. Its documented B connector includes an electronic throttle bridge, a direct wideband sensor connection, two knock inputs, four wheel-speed inputs, ignition outputs 5 and 6 and a second CAN bus. The manufacturer describes an upgrade from Tornado/Tornado 2 requiring a connector change. SXTune 700 hardware reference.
Pinout and connector identification
A1 battery, A2 switched ignition, A3 ground, A4–A7 injector outputs 1–4; A9 crank and A10 cam 1; A11 inlet air temperature and A12 coolant temperature. Connector B: B1–B2 throttle motor, B3–B4 wideband signal, B13–B14 ignition 5–6, B21–B22 knock, B34 CAN2 low and B35 CAN2 high. The complete 700 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune delta700 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
Connector A — AMPSeal 776163-1
| Pin | Name | Description | Notes |
|---|---|---|---|
| A1 | Battery | Power Supply input 6-18V | 12V Permanent Battery Supply (Fuse 15A) |
| A2 | Ignition | Ignition Switch input | Ignition Switch Input (Fuse 5A) |
| A3 | Power Ground 1 | Power Ground | Power Ground (to Battery negative) |
| A4 | Low Side Output 1 | 1.5A Open Collector | Injector Output 1 |
| A5 | Low Side Output 2 | 1.5A Open Collector | Injector Output 2 |
| A6 | Low Side Output 3 | 1.5A Open Collector | Injector Output 3 |
| A7 | Low Side Output 4 | 1.5A Open Collector | Injector Output 4 |
| A8 | Crank/Cam Ground | Digital Ground | Digital Sensor Ground |
| A9 | Crank Input | VR/Hall - Software Selectable | Crankshaft sensor input |
| A10 | Cam Input 1 | VR/Hall - Software Selectable | Camshaft sensor input 1 |
| A11 | NTC Input 1 | 3.16K pull-up to VREF | Inlet Air Temperature Sensor Input |
| A12 | NTC Input 2 | 3.16K pull-up to VREF | Coolant Temperature Sensor Input |
| A13 | Ignition 1 | TTL/Power Ignition Output | Ignition Coil Output 1 |
| A14 | Ignition 2 | TTL/Power Ignition Output | Ignition Coil Output 2 |
| A15 | Ignition 3 | TTL/Power Ignition Output | Ignition Coil Output 3 |
| A16 | Ignition 4 | TTL/Power Ignition Output | Ignition Coil Output 4 |
| A17 | Analog Input 1 | 47k pull-up to VREF | User Defined Analogue Input 1 |
| A18 | Cam Input 2 | VR/Hall - Software Selectable | Camshaft sensor input 2 |
| A19 | Analog Ground 1 | Analog Ground | Analogue Sensor Ground |
| A20 | Narrowband Lambda Input | Weak bias to 450mV | Narrowband Lambda Sensor Input |
| A21 | CAN 1H | CAN bus 1 High | |
| A22 | CAN 1L | CAN bus 1 Low | |
| A23 | Low Side Output 5 | 1.5A Open Collector | User Defined / Injector Output 5 |
| A24 | Low Side Output 7 | 0.75A Open Collector with recirc diode to Vbatt | Main Relay/PWM3 Output |
| A25 | Low Side Output 8 | 1.7A Open Collector with recirc diode to Vbatt | Fuel Pump Relay/PWM4 Output |
| A26 | Low Side Output 9 | 1.7A Open Collector with recirc diode to Vbatt | User Defined PWM1 Output |
| A27 | Low Side Output 10 | 1.7A Open Collector with recirc diode to Vbatt | User Defined PWM2 Output |
| A28 | Low Side Output 11 | 0.75A Open Collector with pull up and diode to VKey | Tacho Output |
| A29 | Low Side Output 6 | 1.5A Open Collector | User Defined / Injector Output 6 |
| A30 | Analog Ground 2 | Analog Ground | Analogue Sensor Ground |
| A31 | NTC Input 3 | 3.16K pull-up to VREF | User Defined Temperature Sensor Input 1 |
| A32 | Analog Input 2 | 47k pull-up to VREF | Throttle Position Sensor 1 Input |
| A33 | Analog Input 3 | 47k pull-up to VREF | Manifold Pressure Sensor Input |
| A34 | VREF1 | 200mA 5V supply to sensors | 5V Sensor Supply output |
| A35 | Power Ground 2 | Power Ground | Power Ground (to Battery negative) |
Connector B — AMPSeal 776163-4
| Pin | Name | Description | Notes |
|---|---|---|---|
| B1 | H Bridge M+ | 8.6A H-Bridge + | Throttle Motor + |
| B2 | H Bridge M- | 8.6A H-Bridge - | Throttle Motor - |
| B3 | Wideband Lambda Ip | LSU Pin 1 | Wideband Lambda Sensor Ip |
| B4 | Wideband Lambda Ia | LSU Pin 5 | Wideband Lambda Sensor Ia |
| B5 | Bipolar Output 1 | 2.5A Hi Side/Lo Side Drive | User Defined PWM5 Output |
| B6 | Bipolar Output 2 | 2.5A Hi Side/Lo Side Drive | User Defined PWM6 Output |
| B7 | Bipolar Output 3 | 2.5A Hi Side/Lo Side Drive | User Defined PWM7 Output |
| B8 | Bipolar Output 4 | 2.5A Hi Side/Lo Side Drive | User Defined PWM8 Output |
| B9 | Low Side Output 12 | 1.5A Open Collector | User Defined / Injector Output 7 |
| B10 | Low Side Output 13 | 1.5A Open Collector | User Defined / Injector Output 8 |
| B11 | Cam Input 3 | Hall Effect Input (2k7 Pull-up to 5V) | Camshaft sensor input 3 |
| B12 | Cam Input 4 | Hall Effect Input (2k7 Pull-up to 5V) | Camshaft sensor input 4 |
| B13 | Ignition 5 | TTL/Power Ignition Output | Ignition Coil Output 5 |
| B14 | Ignition 6 | TTL/Power Ignition Output | Ignition Coil Output 6 |
| B15 | Wideband Lambda Heater | 1.7A Open collector with recirc diode (LSU Pin 3) | Wideband Lambda Sensor Heater Output |
| B16 | WB Lambda Virtual Ground (Vm) | LSU Pin 2 | Wideband Lambda Sensor Vm |
| B17 | Hall Input 1 | Hall Effect Input (2k7 Pull-up to 5V) | Digital Input 1 / Wheel Speed LR |
| B18 | Hall Input 2 | Hall Effect Input (2k7 Pull-up to 5V) | Digital Input 2 / Wheel Speed RR |
| B19 | Hall Input 3 | Hall Effect Input (2k7 Pull-up to 5V) | Digital Input 3 / Wheel Speed LF |
| B20 | Hall Input 4 | Hall Effect Input (2k7 Pull-up to 5V) | Digital Input 4 / Wheel Speed RF |
| B21 | Knock 1 + | Knock Input | Dedicated DSP Knock Input 1 |
| B22 | Knock 2 + | Knock Input | Dedicated DSP Knock Input 2 |
| B23 | Knock Ground | Digital Ground | Analogue Sensor Ground |
| B24 | Wideband Lambda Nernst (Un) | LSU Pin 6 | Wideband Lambda Sensor Un |
| B25 | Analog Input 4 | 47k pull-up to VREF | Throttle Position Sensor 2 Input |
| B26 | Analog Input 5 | 47k pull-up to VREF | Pedal Position Sensor 1 Input |
| B27 | Analog Input 6 | 47k pull-up to VREF | Pedal Position Sensor 2 Input |
| B28 | NTC Input 4 | 3.16k pull-up to VREF | User Defined Temperature Sensor Input 2 |
| B29 | NTC Input 5 | 3.16k pull-up to VREF | User Defined Temperature Sensor Input 3 |
| B30 | Analog Input 7 | 47k pull-up to VREF (optional pull-down to ground) | User Defined Analogue Input 5 |
| B31 | Analog Input 8 | 47k pull-up to VREF (optional pull-down to ground) | User Defined Analogue Input 6 |
| B32 | Analog Input 9 | 47k pull-up to VREF (optional pull-down to ground) | User Defined Analogue Input 7 |
| B33 | Analog Input 10 | 47k pull-up to VREF (optional pull-down to ground) | User Defined Analogue Input 8 |
| B34 | CAN 2L | CAN bus 2 Low | |
| B35 | CAN 2H | CAN bus 2 High |
PC communications connectors
| Pin | Name | Description | Notes |
|---|---|---|---|
| DB9-1 | Ground | ||
| DB9-6 | CAN High | ||
| DB9-7 | CAN Low | ||
| DB9-8 | Battery Voltage | ||
| DTM-1 | Battery Voltage | ||
| DTM-2 | Ground | ||
| DTM-3 | CAN High | ||
| DTM-4 | CAN Low |
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.