Adaptronic eSel039 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda MX-5 / Miata NB8B and NB8C applications, including naturally aspirated and documented turbo variants; the correct basemap and vehicle-specific configuration must be checked. Adaptronic eSel039 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel039 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel039 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
From the Adaptronic eSel039 installation guide, pages 22–27. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 4R has a jumper-dependent turbo versus naturally aspirated assignment; check the application and jumper before wiring.
| Factory pin | Wire colour | Factory function | Adaptronic function | Comments |
|---|---|---|---|---|
| 2A | Y/B | Injector for cylinder 1 | Injector Output 1 | — |
| 2B | R/Y | Cooling fan relay | Aux Output 7 | Fans driven at full speed |
| 2C | L/W | Condenser fan relay | Aux Output 7 | Fans driven at full speed |
| 2D | V/G | Injector for cylinder 2 | Injector Output 4 | — |
| 2E | Lg | EGR valve | MVSS2 | — |
| 2F | W/G | EGR valve | Digital input 8 | — |
| 2G | Y/R | Injector for cylinder 3 | Injector Output 2 | — |
| 2H | P/B | EGR valve | SVSS1 | — |
| 2I | P | EGR valve | SVSS2 | — |
| 2J | Y/G | Injector for cylinder 4 | Injector Output 3 | — |
| 2K | L/B | Aircon relay | Aux Output 8 | — |
| 2M | R/W | Fuel pump relay | Aux Output 5 | Fuel pump output for immobiliser equipped cars |
| 2N | B/W | VTCS solenoid valve | Aux Output 4 | — |
| 2O | R | Fuel pump relay | Aux Output 5 | Fuel pump output for cars with no immobiliser |
| 2P | O | Idle control solenoid valve positive | Connected to 12V ignition power (4AF) | — |
| 2Q | V/R | Idle control solenoid valve negative | Aux Output 1 | — |
| 2R | W/L | Malfunction indicator lamp | Aux Output 6 | — |
| 3A | B | Ground | Power Ground | — |
| 3B | B/R | Ground | Power Ground | — |
| 3C | G/Y | Purge solenoid valve | Digital in 6 | — |
| 3D | Gy/B | EGR boost sensor solenoid valve | Digital in 7 | — |
| 3E | — | NC | — | — |
| 3F | Br/W | Igniter for cylinders 1 and 4 | Ignition output 2 | — |
| 3H | L/O | Main relay | Pulled to ground when the ECU sees more than a 2V on pin 4S (ignition switch input). | Not used on all models. Early models had the main relay driven by the ignition switch directly. |
| 3I | B/Y | Igniter for cylinders 2 and 3 | Ignition output 1 | — |
| 3J | B/O | Front O2 sensor heater | Connected to power ground | — |
| 3K | Y/B | Evap leak detection pump | — | — |
| 3L | — | NC | — | — |
| 3M | Gy/R | Generator control | Driven by regulator in ECU, takes feedback from voltage at pin 4AG | — |
| 3N | — | NC | — | — |
| 3O | G/O | Tachometer | Ignition output 3 | — |
| 3P | W/B | Rear O2 sensor heater | Connected to power ground | — |
| 3Q | G/W | Data link connector | CAS3 | Can be used for flex fuel |
| 3S | R/B | Immobiliser unit | Connected to 12V via 1k resistor | — |
| 3T | G/R | Speedometer signal | MVSS1 | — |
| 3U | Br/R | Generator warning light | Driven by internal circuit, activates light when voltage is < 12.55 V | — |
| 3V | Gy/L | Cam position sensor | CAS 2 input | Pulses for cylinder and TDC identification, and inlet cam position detection |
| 3W | — | NC | — | — |
| 3X | — | NC | — | — |
| 3Y | V/W | Crank position sensor | CAS 1 input | Pulses for calculating ignition timing |
| 3Z | — | NC | — | — |
| 4A | B/L | Ground | Power Ground | — |
| 4B | G | Brake switch | Digital Input 5 | — |
| 4C | Br | Power steering load input | Digital Input 3 | — |
| 4D | Y | Boost control (turbo) VVT positive (NA) | Aux Output 2 | NOTE: Drives high, not low |
| 4E | Y By/Y | Boost control (turbo) Diagnostic (NA) | Connected to pin 4D internally | — |
| 4F | Lg/B | Aircon request input | Digital Input 4 | — |
| 4H | V | Clutch/Neutral switch | Digital Input 2 | — |
| 4I | W/G | Clutch/Neutral switch | Digital Input 1 | — |
| 4J | O | VTCS vacuum switch | — | — |
| 4K | — | NC | — | — |
| 4L | Lg/R | +5V out for sensors | +5V output | — |
| 4M | W | Knock sensor | Knock signal input | — |
| 4N | P/L | Air temperature sensor | Aux Temperature signal input | Mounted in airflow meter |
| 4O | B/R | Sensor ground | Sensor Ground | — |
| 4P | R/L | Engine Coolant Temperature | ECT signal input | — |
| 4R | V/Y | Air temp sensor (turbo) VVT valve negative (NA) | Aux temp input (turbo) Aux output 3 (NA) | Internal jumper to select |
| 4S | B/W | Ignition switch | Triggers 3H output | — |
| 4T | Gy | Generator output voltage | Not used in the regulator | — |
| 4U | — | NC | — | — |
| 4V | G/B | Throttle Position Sensor signal | TPS signal input | — |
| 4W | L | Front O2 sensor signal | O2/EGO signal input | — |
| 4X | P | Air flow meter signal | MAP signal input | AFM signal pin can be used for MAP signal when fitting an external MAP sensor |
| 4Z | P/B | TCM (auto only) | — | — |
| 4AA | R | Rear O2 sensor signal | — | — |
| 4AB | — | NC | — | — |
| 4AC | By/Y V/G | Data link connector Auto TCM | — | Turbo model: Br/Y Auto model: V/G |
| 4AD | Br/B | Fuel gauge sender | — | — |
| 4AE | L/Y | EGR boost sensor | — | — |
| 4AF | W/R | Main relay | +12V Ignition | — |
| 4AG | L/R | Battery constant power | Constant power input | This input is used to measure the battery voltage for the generator control. Therefore it must have power otherwise the generator control will not function. |
| 4AH | R/G | Evap leak detection pump solenoid valve | — | — |
Manufacturer photograph
