Tuning Wiki
Link G4X WRX2X plug-in ECU
Manufacturer product image of WRX2X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X WRX2X is a vehicle-specific programmable plug-in ECU for the Subaru WRX version 1–2 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX2X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The WRX2X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's WRX2X installation manual (2025). Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Applies to the V1–2 WRX/STi and RS Legacy layouts documented by Link. On WRX RA vehicles the fifth injector is wired to pin 25: Link instructs disconnecting its wire or injector, otherwise it is continuously on. The manual says injector drives 7 and 8 are not exposed.

Factory main header positions

Factory pinLink ECU channelFactory function
1Injector 1Injection
55An Volt 3TPS (Main)
2Injector 2Injection
56Ground (TPS)—
3Injector 3Injection
57DI 3Ignition Switch
4Ignition 1Ignition
58DI 4Vehicle Speed
5Ignition 3Ignition
59nc—
6Ignition 2Ignition
60nc—
7Ignition 4Ignition
61nc—
8Aux 7Purge
62nc—
9nc—
10Injector 5 (Aux)Fan Relay 2
71Ground (Signal)—
11Aux 4Wastegate Solenoid
72Ground (AFM)—
12Aux 2ISC Open (ISC Solenoid)
73An Volt 2AFM Signal
13Aux 1ISC Close (ISC Slave)
74AFM +12V—
14Injector 4Injection
75An Temp 1ECT
15Ground—
76An Volt 4Oxygen Sensor Signal
16Ground—
77nc—
17Aux 5Fuel Pump Relay
78An Volt 1Factory MAP Sensor
18Aux 6A/C Out
79+5V Out (MAP)—
19nc—
80+14VECU Power
20nc—
81nc—
21Aux 8CE Light
82Ground (Signal)—
22nc—
83Ground (MAP)—
23Injector 6 (Aux)Fan Relay 1
84nc—
24nc—
85nc—
25Ground—
86nc—
26Ground—
87Ground (O2 Shield)—
88nc—
31nc—
89nc (+12V constant)—
32nc—
90nc—
33nc—
91+14VECU Power
34Knock 1Knock
92nc—
35Ground (Knock)—
36Ground (Trig 2 Shield)—
37Ground (Trig 2)—
38Trig 2Trig 2
39Aux 3Tacho
40nc—
41nc—
42nc—
43nc—
44nc—
45DI 1Start Signal
46DI 2A/C In
51Ground (Trig 1 Shield)—
52Ground (Trig 1)—
53Trig 1Trig 1
54+5V Out—

Expansion connector

PinLink ECU channelFactory function
1Ground (Signal)—
2+5V Out—
3DI 5—
4DI 6—
5An Volt 5—
6An Volt 6—
7An Temp 2—
8An Temp 3—
9Ground (Signal)—
10+5V Out—
11DI 9—
12DI 10—
13An Volt 8—
14An Volt 9—
15Ignition 7 (Aux)—
16Ignition 8 (Aux)—

CAN 1/RS232 Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN1 LGreen
3CAN1 HWhite
4RS232-RXGrey
5RS232-TXYellow

CAN 2/OBD Connector

PinFunctionWire colour
1GNDBrown
2CAN2 LGreen
3CAN2 HWhite
4NCGrey
5+14VYellow

Directly applicable articles

Technical articles assigned to this context will appear here.