
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V1 S7Plus, with product code S7Plus-RS38V1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Audi RS3/TTRS 8V1 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to CZGB engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another; verify that conflicting assignment with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.
Connector A
| Pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | Main Relay |
| A2 | H-Bridge1 / SlaveOut1 | H-Bridge1 | DBW + |
| A3 | H-Bridge2 / SlaveOut2 | H-Bridge2 | DBW - |
| A4 | H-Bridge3 / SlaveOut3 | H-Bridge3 | Tacho Wire |
| A5 | H-Bridge4 / SlaveOut4 | H-Bridge4 | Fan |
| A6 | H-Bridge5 / SlaveOut5 | H-Bridge5 | Valve for Oil Pressure Control |
| A7 | H-Bridge6 / SlaveOut6 | H-Bridge6 | Starter Relay |
| A8 | H-Bridge7 / SlaveOut7 | H-Bridge7 | Charcoal Solenoid |
| A9 | H-Bridge8 / SlaveOut8 | H-Bridge8 | Intake Fuel Pump |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Primary Injector 4 |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | Primary Injector 5 |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | Port Injector 1 (External) |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | Port Injector 2 (External) |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | Port Injector 3 (External) |
| A18 | FUEL9 | INJECTOR or PWM OUTPUT | Port Injector 4 (External) |
| A19 | FUEL10 | INJECTOR or PWM OUTPUT | Port Injector 5 (External) |
| A20 | FUEL11 | INJECTOR or PWM OUTPUT | Exhaust Flap |
| A21 | FUEL12 | INJECTOR or PWM OUTPUT | Boost Solenoid |
| A22 | FUEL13 | INJECTOR or PWM OUTPUT | Turbo Recirc (N249) |
| A23 | FUEL14 | INJECTOR or PWM OUTPUT | Intake Flap Control Solenoid |
| A24 | FUEL15 | INJECTOR or PWM OUTPUT | VVT1 Int (N205) |
| A25 | FUEL16 | INJECTOR or PWM OUTPUT | VVT1 Ex (N316) |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | IGN1 (N70) |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | IGN2 (N127) |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | IGN3 (N291) |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | IGN4 (N292) |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | IGN5 (N292) |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | DI Pump Control |
| A32 | PWRGND | POWER GROUND | PwrGnd |
| A33 | PWRGND | POWER GROUND | PwrGNd |
| A34 | PWRGND | POWER GROUND | PwrGNd |
Connector B
| Pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | PWRGROUND |
| B2 | CAN2L | — | — |
| B3 | CAN2H | — | — |
| B4 | KNOCK | KNOCK | Knock + |
| B5 | KNOCK 2 | KNOCK 2 | — |
| B6 | PVBAT | CONSTANT 12V | — |
| B7 | IVBAT | 12v | — |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | Pin6 on LSU4.9 Connector |
| B9 | LAM1B | Lami / LamD1- /LamIP1 | Pin1 on LSU4.9 Connector |
| B10 | LAM1C | LamLIA1 | Pin5 on LSU4.9 Connector |
| B11 | LAM1D | LamGND / LamLVM1 | Pin2 on LSU4.9 Connector |
| B12 | LAM1HEATER | LAMBDA HEATER | Pin3 on LSU4.9 Connector |
| B13 | IVBAT | 12 V | — |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | — |
| B15 | LAM2B | Lami / LamD1- /LamIP1 | — |
| B16 | LAM2C | LamLIA1 | — |
| B17 | LAM2D | LamGND / LamLVM1 | — |
| B18 | LAM2HEATER | Slave Out 10 | — |
| B19 | IVBAT | 12 V | — |
| B20 | KLINE | Kline | — |
| B21 | RS232RX | RS232RX | — |
| B22 | RS232TX | RS232TX | — |
| B23 | LANRX- | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX- | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| Pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| C1 | KNOCKGND | KNOCKGND | Knock - |
| C2 | ANGND | SENSOR GND | — |
| C3 | ANGND | SENSOR GND | — |
| C4 | ANGND | SENSOR GND | — |
| C5 | 5V OUT | 5V OUT | — |
| C6 | 5V OUT | 5V OUT | — |
| C7 | 5V OUT | 5V OUT | — |
| C8 | CAN L | Can Low | Powertrain Can |
| C9 | CAN H | Can High | Powertrain Can |
| C10 | AN01 | BI-POLAR INPUTS | Di Pressure |
| C11 | AN02 | BI-POLAR INPUTS | MapSensor |
| C12 | AN03 | BI-POLAR INPUTS | Charge Pressure |
| C13 | AN04 | BI-POLAR INPUTS | Brake |
| C14 | AN05 | UNI-POLAR INPUTS | — |
| C15 | AN06 | UNI-POLAR INPUTS | VVT1Ex Pos |
| C16 | AN07 | UNI-POLAR INPUTS | Crank Sensor |
| C17 | AN08 | UNI-POLAR INPUTS | Starter Request |
| C18 | AN09 | VOLT-INPUTS | TPS1A |
| C19 | AN10 | VOLT-INPUTS | TPS1B |
| C20 | AN11 | VOLT-INPUTS | PPSA |
| C21 | AN12 | VOLT-INPUTS | PPSB |
| C22 | AN13 | RESISTIVE INPUTS | — |
| C23 | AN14 | RESISTIVE INPUTS | Intake Air Temp |
| C24 | AN15 | RESISTIVE INPUTS | Coolant Temp |
| C25 | AN16 | RESISTIVE INPUTS | Oil Pressure Sw |
| C26 | EGT1- | EGT1 - | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | Key On sig (15) |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | Oil Level / Temp |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | — |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | — |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | — |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | LowFuel Pressure |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | Intake Flap Pos |