Simos 8.6, also written 8.60, is associated with Audi 2.8-litre V6 FSI CHVA examples in aftermarket conversion and tool records. Audi training material uses a different Simos suffix for a CHVA example, so the engine code alone does not settle the ECU identification. The sources are examples, not a complete fitment list or verified map description.
Processor
A tool-vendor bench-clone guide for the CGDI FC200 names the controller in its bench-mode selection as "Continental Simos8.6 TC1796", that is, an Infineon TriCore TC1796 microcontroller, and gives its example vehicle as an Audi A6 2014 TFSI. This is a single vendor listing and not Continental documentation; it does not tie the TC1796 to the CHVA engine, and flash and EEPROM part details are not given. AutoTuner's compatibility list (28 October 2026) lists the related Simos 8.4 and 8.5 with the same TC1796 but has no Simos 8.6 entry. [5] [6]
Applications and identification
A 2013 Prins conversion manual identifies an Audi A6 2.8 CHVA automatic with the petrol ECU labelled Simos 8.60. Its title in the PDF's web address names a different engine code; the application stated inside the document is CHVA. The manual is for an aftermarket LPG conversion, so its converted fuel-system layout must not be assumed to describe an unmodified vehicle. [1]
Magicmotorsport's Flex 4.8.0.0 vehicle list also names 2010 Audi A7 2.8 FSI CHVA entries as Simos 8.6. A workshop example reports an A6 CHVA with identifier 4G0907552D and software 0004; those numbers identify that case, not all 8.6 ECUs. Record the actual hardware, full software and calibration identifiers, engine code and installed modifications. [2] [3]
Conflicting CHVA suffix descriptions
Audi's Self-Study Programme 603, page 13, lists its A6 Avant '12 CHVA 2.8-litre example with Simos 8.1, while the Prins manual and Flex list above describe CHVA examples as 8.60/8.6. The source descriptions disagree; the available records do not establish whether that reflects different installations, naming conventions or an error. Neither source proves that every CHVA has one suffix or that both necessarily occur in production.
Read the actual ECU diagnostic identification and part, hardware and software numbers and verify the controller with the tool provider before selecting a protocol or a calibration. Neither engine code, approximate power nor model year is enough to resolve this conflict. Audi's programme also refers readers to SSP 411 for the 2.8 FSI engine's general design; that earlier document describes Simos 8.1 examples and does not validate an 8.6 map or file. See the Simos 8.1 overview for its documented BDX and CALA examples.
Access and tool coverage
The historical Flex vehicle list gives OBD as the connection mode for its A7 CHVA entries. Separately, an Auto-Krak service page describes an unlock procedure for example Simos 8.6 units and says it can subsequently write by OBD or bench. An E-VAG case reports that its 4G0907552D 0004 required opening and unlocking. These are product- and case-specific claims: an OBD listing on its own does not establish whether a particular ECU is locked, needs preparation, or supports the read, write and recovery functions required. [2] [4] [3]
Check current tool documentation for the exact ECU and software, including any unlock prerequisites, checksum handling, file scope and recovery options. Identify whether a read is physical, calibration-only or a supplied virtual original before relying on it for recovery.
PCMflash's module 57 manual, page 49, states that its Simos 8.6 calibration reading and writing follows a bootloader-mode unlock; it separately lists EEPROM read, write and unlock functions. This is the provider's protocol-specific scope, not a requirement established for every tool or a promise of a complete recoverable image. Check the current documentation for the actual unit and operation.
Calibration-only reads and version matching
A third-party English rendering of the PCMflash module 57 instructions states that, in its documented Simos 8.6 workflow, the actual read after unlocking contains the calibration area rather than the complete software. It warns that a calibration-only write must match the software version already in the ECU. The same description distinguishes this from its supplier-provided stock-file database, which it says can support a software update. These are descriptions of that particular tool and workflow, not a guarantee that an update or a different tool is compatible with the controller in hand.
Record the original ECU software and calibration identifiers before and after any authorised update, as well as the tool, operation, file size and memory areas obtained. Check the supplier's current compatibility and recovery instructions rather than using a calibration from a different software version solely because the part number or file size looks similar. An EEPROM image and a calibration-area file have different scope; neither alone proves that all data needed to restore a particular unit has been captured. The provider’s PCMflash manual separately lists EEPROM/unlock and calibration operations for 8.6. Do not generalise these instructions to other tools or versions.
Tuning and diagnostics
No verified Simos 8.6 map addresses, units or control strategy have been established by the sources listed here. Use software-matched definitions and verify them against the actual file; do not transfer maps or performance figures from Simos 8.1, 8.2, 8.4 or 8.5. For a baseline, review fault codes and compare available engine load, throttle, lambda, individual-cylinder knock correction and requested versus actual fuel pressure over repeatable runs. Diagnostic channel availability and interpretation depend on the exact software and tool.
Sources
- Prins, Direct LiquiMax-2.1 A6 application installation manual, 2013: document's CHVA and Simos 8.60 identification.
- Magicmotorsport, Flex 4.8.0.0 vehicle list: A7 CHVA entries and listed connection mode.
- E-VAG, A6 CHVA workshop case (Russian): specific identifier and stated access requirement.
- Auto-Krak, Simos 8.6 unlock service (Polish): provider's example ECU numbers and claimed workflow.
- CGDI blog, FC200 Audi Simos 8.6 ECU clone guide, January 2026: bench-mode listing "Continental Simos8.6 TC1796", example vehicle Audi A6 2014 TFSI. Tool-vendor blog. Accessed 19 November 2026.
- AutoTuner ECU compatibility list, export dated 28 October 2026. Tool-vendor MCU listing for Simos 8.4 and 8.5; no 8.6 entry. Accessed 19 November 2026.