An intake upgrade is only a performance upgrade when it delivers more or cooler air to the engine in the speed range that matters. This page explains where an intake loses pressure, why the air's temperature matters, and how to measure the difference. For the throttle body and manifold side see throttle bodies and airflow and inlet manifolds and runner length. A model-specific example is EA113 and EA888 intake upgrade comparison.
Where an intake restricts
Air loses pressure at every restriction between the atmosphere and the cylinder. The figures below are measured examples on particular cars from an HP Academy webinar on intake restrictions. They show the size of effects that have been seen, not gains to expect.
- Filter element. A factory element can be restrictive, but the gain from changing it varies. On one engine the best filter swap added only about 1 to 1.5 kW at the wheels, which is close to the run-to-run variation of a dyno.
- Airbox and inlet ducting. Convoluted paths, resonant chambers and sharp-edged inlets add restriction. On the same engine a flared, larger inlet added roughly 2 to 3 kW at the top end.
- Airflow meters. Some meters restrict noticeably. Removing a trap-door meter was worth about 12 to 15 wheel hp on one turbo engine, and a small-diameter meter cost about 10 to 15 hp on one V8, while later versions with larger meters gained almost nothing.
- Hoses and bends. Corrugated hoses roughen the airflow and sharp bends add restriction. On one rally engine, about 150 mm of straight pipe before a bend was worth roughly 20 wheel hp.
- Turbo inlet. A restriction before the compressor lowers the inlet pressure, which raises the compressor's pressure ratio and heats the charge for the same boost reading. A boost gauge alone does not show this. See forced induction.
A few horsepower of restriction is often not worth chasing, while 10 to 15 hp usually is. Bigger is not always better either: an oversized pipe ahead of a turbo gains nothing if the turbo inlet is the choke point.
Air temperature
Hot engine-bay air is less dense and carries less oxygen. Each 10 °C rise cuts air density by roughly 2.5 to 3 per cent, so swapping a factory airbox for an open pod filter inside the engine bay can lose power despite the better flow. Ducting cool air to the filter and heat-shielding it help, and intake air temperature should be logged to see the real effect. The same idea applies after the compressor: see charge cooling.
A published test of a Toyota GR Supra intake kit shows why both flow and temperature need measuring. Mishimoto's results show restriction down by 17 per cent on a flow bench at 200, 400 and 600 CFM, and a heat shield lowering intake air temperature by 4 °F, yet the dyno gave the same power with the stock and aftermarket intakes. The car uses speed-density control, so the ECU detected the airflow change and adjusted fuelling to compensate. The kit's maker expects a benefit with more aggressive tunes or larger turbos. These are one manufacturer's results, and the exact flow and power readings are in charts rather than text. Bench flow is not engine power.
Measuring instead of guessing
- Ramp-run manifold pressure on a naturally aspirated engine. A drop below atmospheric pressure at full throttle indicates restriction; on a stock Toyota 86, manifold pressure fell from 0.98 bar to 0.92 bar at high rpm. This shows that restriction exists but not where.
- A spare pressure sensor moved to different points along the intake, or a water manometer at a chosen point, isolates the restriction stage by stage.
- Staged swaps. Change one component at a time and test, so the gain can be attributed.
- Removing the whole intake shows the best achievable result and whether the restriction is worth chasing.
Compare like with like: the same test method, conditions and intake air temperature, with the hood position and cooling documented, as set out in the validation list on engine performance upgrades and dynamometer measurement and interpreting results.
Airflow meters and calibration
A change to the airflow meter, its housing or the pipe around it changes what the ECU measures. Do not switch to speed density unless the meter is known to be restrictive; a properly calibrated, unrestrictive meter can make tuning quicker. Oiled filters can also contaminate hot-wire sensing elements over time and upset their accuracy. See engine load sensing: speed density, Alpha-N and MAF and common MAF sensor faults. After an intake change, check the mixture with a wideband sensor: air-fuel ratio and wideband lambda sensors.
Sources
- 237 | Air Intake Restrictions Explained. High Performance Academy webinar. Sources of restriction, temperature effect and measurement methods; figures are measured examples on particular cars. Accessed 2026-11-19.
- Speed Evolved - Performance Intake Kit R&D, Part 4 - Testing Results. Mishimoto, 13 October 2020. Flow-bench, dyno and intake-temperature results for one manufacturer's kit. Accessed 2026-11-19.