Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota GR Yaris, with product code SGDI-Yaris. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota GR Yaris installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Toyota GR Yaris product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
26-way additional I/O header
The Syvecs application manual documents the rear additional I/O header. This is not the OEM vehicle connector pinout. Verify hardware revision, connector view, current limits and configuration; a pin labelled available may be assigned to an existing device.
Rev1 hardware, 2022–2023
| Pin | Syvecs function | Source note |
|---|---|---|
| 1 | Ground | — |
| 2 | K-type − | — |
| 3 | K-type + | — |
| 4 | GDI4− | — |
| 5 | GDI4+ | — |
| 6 | DensoHtr1 / Slave1Out1 | Spare output if OEM Denso is not used |
| 7 | Vbat | 12 V bench supply or NTK lambda heater output |
| 8 | Fuel11 | Spare output |
| 9 | RS232 RX | — |
| 10 | Lam1v | NTK L2H2 gray wire |
| 11 | Lam1i | NTK L2H2 white wire |
| 12 | LamGnd | NTK L2H2 black wire |
| 13 | Vbat-– | Source describes 12 V bench supply or NTK heater output; confirm label |
| 14 | Out3 / Slave1Out3 | Spare output |
| 15 | RS232 TX | — |
| 16 | CAN2L | Expansion / dashboard CAN low |
| 17 | CAN2H | Expansion / dashboard CAN high |
| 18 | CAN3L | Expansion / dashboard CAN low |
| 19 | CAN3H | Expansion / dashboard CAN high |
| 20 | Out4 / Slave1Out4 | Spare output |
| 21 | H-Bridge5 | — |
| 22 | H-Bridge6 | — |
| 23 | LAN RX− | Orange/white |
| 24 | LAN RX+ | White/orange |
| 25 | LAN TX− | Green/white |
| 26 | LAN TX+ | White/green |
Rev2 hardware, purchases from 2024 onwards
| Pin | Syvecs function | Source note |
|---|---|---|
| 1 | Ground | — |
| 2 | K-type − | — |
| 3 | K-type + | — |
| 4 | GDI4− | — |
| 5 | GDI4+ | — |
| 6 | Out1 / Slave1Out1 | Spare output if OEM Denso is not used |
| 7 | Vbat | 12 V bench supply or NTK lambda heater output |
| 8 | Fuel11 | Spare output |
| 9 | RS232 RX | — |
| 10 | Lam1v | NTK L2H2 gray wire |
| 11 | Lam1i | NTK L2H2 white wire |
| 12 | LamGnd | NTK L2H2 black wire |
| 13 | Vbat-– | Source describes 12 V bench supply or NTK heater output; confirm label |
| 14 | 5 V regulated supply | — |
| 15 | RS232 TX | — |
| 16 | CAN2L | Expansion / dashboard CAN low |
| 17 | CAN2H | Expansion / dashboard CAN high |
| 18 | CAN3L | Expansion / dashboard CAN low |
| 19 | CAN3H | Expansion / dashboard CAN high |
| 20 | Out4 / Slave1Out4 | Spare output |
| 21 | AN01 | Input |
| 22 | S1AN05 / Slave1AN05 | Input |
| 23 | LAN RX− | Orange/white |
| 24 | LAN RX+ | White/orange |
| 25 | LAN TX− | Green/white |
| 26 | LAN TX+ | White/green |
Pin 13 is written “Vbat-–” while the same sentence describes a 12 V supply or heater output. Confirm the polarity with Syvecs for the actual hardware before connecting it. The source does not provide the full OEM vehicle main-connector schedule here.