
MaxxECU BMW M54 MS42 MS43 GEN2 plug-in adapter joins a compatible GEN2 ECU to a specified factory engine harness. This is a vehicle-specific adapter system, not a different universal ECU model. Manufacturer's installation guide.
Applicability
MaxxECU identifies a GEN2 TRACK/RACE adapter for documented MS42/MS43 applications and explicitly excludes MS45. Its guide states manual transmission only; some vehicle combinations are marked unverified. Confirm exact engine, original ECU and connector, as source tables group several engine capacities. Check the exact vehicle, engine, ECU number, harness and hardware revision against the manufacturer guide before purchasing or installing.
Manufacturer's function mapping
These assignments are specific to the documented GEN2 adapter and ECU configuration, not a universal vehicle pinout. Confirm calibration, connector face and configuration in the source.
| Options | OEM ECU PIN | MaxxECU IO | GEN2 TRACK | GEN2 RACE | Note |
|---|---|---|---|---|---|
| 6 injection sequential | C33, C34, C35, C36, C37, C38 | INJ 1-6 | YES | YES | |
| 6 ignition sequential (using IGBT) | E3, E2, E1, E9, E8, E7 | IGN 1-6 | YES | YES | |
| Fuel pump | D10 | GPO 1 | YES | YES | |
| Thermostat | C45 | GPO 2 | YES | YES | |
| FAN (PWM) | D4 | GPO 3 | YES | YES | |
| ECU relay activation | B23 | GPO 4 | YES | YES | |
| VANOS solenoid (exhaust) | C41 | GPO 5 | YES | YES | |
| VANOS solenoid (intake) | C40 | GPO 6 | YES | YES | |
| Lambda heater- | GPO 7 | YES | YES | ||
| Fuel tank vent valve | C42 | GPO 8 | YES | YES | |
| E-Throttle with cruise control | C44, C43 | GPO 13/GPO 14 | YES | YES | |
| Idle solenoid (MS42 only) | C46, C47 | IGN 7/8 | YES | YES | Not used for idle features using our base tune, but it is still wired... |
| DISA (intake) | C49 | INJ 7 | YES | YES | |
| AC magnetic clutch* | D29 | INJ 8 | YES | YES | Parallel to OEM A/C clutch (D29). Disconnect A/C to use as a general output. |
| OEM knock sensors | C29, C31 | KNOCK1, KNOCK2 | YES | YES | |
| Exhaust flap | D18 | Yes, no ctrl | Yes, no ctrl | Only available on M54B30, this output is always active (no control option available) | |
| External boost solenoid | GPO 9 (12V) | YES | YES | ||
| Crank trigger | C8 | PULSE 1 | YES | YES | |
| Intake CAM trigger | C5 | PULSE 2 | YES | YES | |
| Exhaust CAM trigger | C2 | PULSE 3 | YES | YES | |
| BMW Steering wheel buttons | D27 | PULSE 4 | YES | YES | |
| OE coolant temperature sensor (CLT) | C24 | AIN 1 | YES | YES | |
| OE intake air temperature sensor (IAT) | C22 | AIN 2 | YES | YES | |
| OE throttle position sensor (main) | C19 | AIN 3 | YES | YES | |
| OE throttle position sensor (backup) | C10 | AIN 4 | YES | YES | |
| OE engine oil temperature sensor | C27 | AIN 5 | YES | YES | No calibration available for this sensor. |
| OE Coolant outlet temperature | D39 | AIN 6 | YES | YES | |
| OE pedal sensor (main) | D13 + C16 (MS42) | AIN 7 | YES | YES | |
| OE pedal sensor (backup) | D8 + C9 (MS42) | AIN 8 | YES | YES | |
| OE clutch switch | D23 | AIN 9 | YES | YES | |
| Brake switch | BMW E46 330i (MS43) CAN | ||||
| Secondary air pump | - | - | |||
| Wideband lambda sensor | Using external harness (included) | ||||
| OE mass air mass flow sensor | - | - | NO | NO | |
| Oil pressure switch | C26 (MS43) / D11 (MS42) | NO | NO | ||
| Oil level switch (MS42 only) | C39 | NO | NO | ||
| Instrument cluster | BMW E46 330i (MS43) CAN | ||||
| Bluetooth ( MDash) | |||||
| EGT option | NO | Yes |
Additional connector
The model-specific guide provides the following extra connector positions. Check its drawing for the view and pin labels; available outputs differ between TRACK and RACE.
| Pin | GEN2 TRACK | GEN2 RACE | Usage | Note |
|---|---|---|---|---|
| 1 | +5V sensor supply | +5V sensor supply | Power source for external sensors | |
| 2 | Sensor GND | Sensor GND | Sensor ground for external sensors | |
| 3 | AIN 10 | AIN 10 | 0-5V analog input | |
| 4 | AIN 11 | AIN 11 | 0-5V analog input | |
| 5 | AIN 12 | AIN 12 | 0-5V analog input | |
| 6 | PULSE5+ | AIN 17 | ||
| 7 | +12V switched | +12V switched | Battery positive (+12V) | Output at ignition on |
| 8 | INJ 8 | INJ 8 | Output | Parallel to OEM A/C clutch (D29). Disconnect A/C to use as a general output. |
| 9 | GPO 10 (+12V) | GPO 10 (+12V) | Output | |
| 10 | GPO 11 (+12V) | GPO 11 (+12V) | Output | |
| 11 | CAN2 L | AIN 20 | Different function depending on used MaxxECU | |
| 12 | CAN2 H | AIN 21 | Different function depending on used MaxxECU |
Documents and wiring
See the exact adapter and pinout guide for additional connectors, wideband wiring, power feeds, fuses and any limitations. The GEN2 plug-in index and MaxxECU family reference cover other hardware and applications. Review firmware and functions for the specific setup.
Source reviewed 17 November 2026.