MaxxECU MINI — Compact entry ECU with four injector and four ignition outputs; up to four fully sequential cylinders or eight in wasted spark. MaxxECU product information.

Model identification and capabilities
A 400 kPa absolute MAP sensor is built in. The MINI has one VR/Hall trigger, two extra Hall/digital inputs and two extra 0–5 V analogue inputs in addition to its named temperature and throttle inputs. The manufacturer specifies four auxiliary outputs and 8 MB of internal logging, up to 1000 Hz. CAN and USB are available. Manufacturer specification; MaxxECU model comparison.
| Sequential cylinders, maximum | 4 |
|---|---|
| Injector outputs | 4 high-impedance |
| Ignition outputs | 4 |
| Configuration | MTune; check the release appropriate to the ECU and hardware revision |
Identification and installation
It does not include an internal wideband controller: use the documented external analogue or CAN solution. Injector outputs are intended for high-impedance injectors; observe the manufacturer’s instructions for low-impedance injectors and external current limiting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
MINI connector 1, REV10+; see the linked manufacturer drawing for the connector face and its cavity positions. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | TRIGGER | |
| A2 | TRIGGER GND | |
| A3 | Not assigned in source | |
| A4 | Not assigned in source | |
| B1 | DIN 1 (Hall onLY) | |
| B2 | DIN 2 (Hall only) | |
| B3 | SENSOR GND | |
| B4 | SENSOR GND | |
| C1 | CLT | |
| C2 | IAT | |
| C3 | AIN 3 (0-5V) | |
| C4 | AIN 4 (0-5V) | |
| D1 | GPO 8/TACHO | 660ohm pullup |
| D2 | TPS | |
| D3 | GND Shield | |
| D4 | SENSOR GND | |
| E1 | GPO 3 | |
| E2 | +5V sensor supply | (peak 0.5A, max 150mA) |
| E3 | CAN L | Read important note below if you encounter issues with CAN communications! |
| E4 | CAN H | Read important note below if you encounter issues with CAN communications! |
| F1 | IGN 1 | |
| F2 | IGN 2 | |
| F3 | IGN 3 | |
| F4 | IGN 4 | |
| G1 | GPO 2 | |
| G2 | GPO 1 | |
| G3 | INJ 1 | |
| G4 | ENGINE GND | |
| H1 | INJ 2 | |
| H2 | INJ 3 | |
| H3 | INJ 4 | |
| H4 | +12V (ECU power supply) |
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
MaxxECU reports that approximately the first 100 MINI harnesses delivered in 2019 had CAN H and CAN L swapped in harness labelling; ECU positions remain E4 CAN H and E3 CAN L. Verify the actual loom against the manufacturer’s harness notice.
Software and further documents
- MaxxECU MINI: product information
- Model wiring and pinout reference
- MTune, quick-start guides and revision-specific wiring downloads
- MaxxECU family overview
Sources reviewed 17 November 2026.