Wolf V500 is a standalone or earlier programmable engine-management system. The 2006 Wolf V500 manufacturer specification describes PC calibration, fuel and ignition control, auxiliary functions and onboard fault reporting. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Wolf V500 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
V500 connector pinout
Positions are transcribed from the Wolf 3D V500 connector list. Confirm the wiring diagram and version for the unit before connecting: the V550 has different documented functions on some B-connector pins. Consult the source for connector orientation, wire specification and electrical limits.
Connector A — 34 positions
| Pin | Function in source |
|---|---|
| A1 | +12 V input |
| A2 | A/C request input |
| A3 | Idle air PWM |
| A4 | Injector output 1 |
| A5 | Injector output 2 |
| A6 | Injector output 3 |
| A7 | Injector output 4 |
| A8 | Injector output 5 |
| A9 | Injector output 6 |
| A10 | Fuel pump output |
| A11 | Boost control PWM |
| A12 | Ignition output 1 |
| A13 | Ignition output 2 |
| A14 | Ignition output 3 |
| A15 | Ignition output 4 |
| A16 | Ignition output 5 |
| A17 | Ignition output 6 |
| A18 | +5 V engine sensors |
| A19 | Throttle position input |
| A20 | Engine temperature input |
| A21 | Air temperature input |
| A22 | Sensor ground |
| A23 | Tachometer output |
| A24 | Thermofan output |
| A25 | RS232 RXD |
| A26 | Power ground |
| A27 | Power ground |
| A28 | Trigger reference signal |
| A29 | Trigger reference sensor ground |
| A30 | Trigger sync signal |
| A31 | Oxygen sensor 1 signal |
| A32 | Oxygen sensor 1 signal ground |
| A33 | Oxygen sensor 1 pump output |
| A34 | RS232 TXD |
Connector B — 26 positions
| Pin | Function in source |
|---|---|
| B1 | Injector output 7 |
| B2 | Injector output 8 |
| B3 | Auxiliary low-side 1 |
| B4 | Auxiliary low-side 2 |
| B5 | Auxiliary low-side 3 |
| B6 | Auxiliary low-side 4 |
| B7 | Auxiliary low-side 5 |
| B8 | Ignition output 7 |
| B9 | Ignition output 8 |
| B10 | Auxiliary low-side 6 |
| B11 | Auxiliary low-side 7 |
| B12 | Turbo timer relay |
| B13 | Turbo timer sense |
| B14 | Auxiliary high/low-side 1 |
| B15 | Auxiliary high/low-side 2 |
| B16 | Auxiliary high/low-side 3 |
| B17 | Auxiliary high/low-side 4 |
| B18 | Auxiliary high/low-side 5 |
| B19 | Auxiliary high/low-side 6 |
| B20 | +5 V auxiliary output |
| B21 | MAP / MAF sensor input |
| B22 | +8 V auxiliary output |
| B23 | Oxygen sensor 2 signal |
| B24 | Oxygen sensor 2 pump output |
| B25 | Not used |
| B26 | Not used |