
Avenger EFI is a Holley EFI engine-management system offered in throttle-body and multiport kits. The Avenger installation manual describes a J1A 34-pin input connector and J1B 26-pin output connector with eight injector outputs, alongside its handheld interface. The 4-barrel MPFI guide records specific Chevrolet packages.
Wiring and tuning
Connector shape alone does not establish compatibility with HP, Dominator or Terminator. Use the Avenger-specific diagram, exact kit and ignition/engine harness, and consult the manufacturer's handheld and software documentation. The manual states that the Avenger's USB connector is not used for its normal handheld setup.
See the Holley EFI manufacturer index. Sources reviewed 17 November 2026.
Avenger system ECU pinout
The Holley Avenger installation manual, Appendix 1, lists these P1A and P1B connector cavities. The manufacturer marks some pins as unused on Avenger even if a harness wire is populated. Match the system version and connector view to the source, and follow its electrical and grounding instructions.
P1A connector
| Pin | Function |
|---|---|
| A1 | Coil − input |
| A2 | Fuel pump out (+12 V, 10 A maximum) |
| A3 | Unused on Avenger (may be populated) |
| A4 | Unused on Avenger (may be populated) |
| A5 | TPS input |
| A6 | Unused on Avenger (may be populated) |
| A7 | WB1 COMPR2 |
| A8 | WB1 shield |
| A9 | Wideband heater − |
| A10 | Switched +12 V input |
| A11 | Manifold air temperature input |
| A12 | Unused on Avenger (may be populated) |
| A13 | Unused on Avenger (may be populated) |
| A14 | Cam/crank ground |
| A15 | Gauge digital output |
| A16 | WB1 COMPR1 |
| A17 | WB1 VS− / IP+ |
| A18 | Sensor ground |
| A19 | Engine coolant temperature input |
| A20 | Oil pressure input |
| A21 | Unused on Avenger (may be populated) |
| A22 | Cam sync input / ignition bypass output |
| A23 | MAP sensor input |
| A24 | CAN low |
| A25 | WB1 VS+ |
| A26 | Sensor +5 V |
| A27 | Not used |
| A28 | EST / SPOUT output |
| A29 | Unused on Avenger (may be populated) |
| A30 | Crank speed input |
| A31 | Fuel pressure input |
| A32 | CAN high |
| A33 | WB1 IP+ |
| A34 | Wideband heater + |
P1B connector
| Pin | Function |
|---|---|
| B1 | IAC A low |
| B2 | IAC A high |
| B3 | Fan #2 output (ground) |
| B4 | Injector F output |
| B5 | Injector G output |
| B6 | Injector H output |
| B7 | Injector E output |
| B8 | IAC B low |
| B9 | IAC B high |
| B10 | Fan #1 output (ground) |
| B11 | Unused on Avenger (may be populated) |
| B12 | A/C shutdown (+12 V) |
| B13 | Injector D output |
| B14 | Unused on Avenger (may be populated) |
| B15 | Unused on Avenger (may be populated) |
| B16 | Unused on Avenger (may be populated) |
| B17 | Unused on Avenger (may be populated) |
| B18 | Unused on Avenger (may be populated) |
| B19 | Injector A output |
| B20 | EST 12 V output |
| B21 | Unused on Avenger (may be populated) |
| B22 | Unused on Avenger (may be populated) |
| B23 | Unused on Avenger (may be populated) |
| B24 | Unused on Avenger (may be populated) |
| B25 | Injector C output |
| B26 | Injector B output |