
Link G4X HC96X is a vehicle-specific programmable plug-in ECU for the Honda CivicLink 98 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HC96X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The HC96X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's HC96X installation manual (2025). The manual states that pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. The manufacturer identifies two CAN buses. Aux 5 and Aux 6 use high-side circuitry on the bottom board but are configured as low-side drives in PCLink; injector drives 7 and 8 are not exposed. The manufacturer assigns both A-5 and A-6 to injector 5, for the two oxygen-sensor heaters.
Main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| A-1 | Injector 4 | Injection |
| C-1 | Ground | — |
| A-2 | Injector 3 | Injection |
| C-2 | Ground (Trig 1) | — |
| A-3 | Injector 2 | Injection |
| C-3 | Ground | — |
| A-4 | Injector 1 | Injection |
| C-4 | Ground (Trig 2) | — |
| A-5 | Injector 5 (Aux) | Oxy Heater (Secondary) |
| C-5 | DI 1 | A/C Request |
| A-6 | Injector 5 (Aux) | Oxy Heater (Primary) |
| C-6 | DI 2 | Start Signal |
| A-7 | Aux 5 | Intake Runner Solenoid (Integra Only) |
| C-7 | nc | — |
| A-8 | Aux 6 | VTEC Solenoid (High Side) |
| C-8 | nc | — |
| A-9 | Ground | — |
| C-9 | nc | — |
| A-10 | Ground | — |
| C-10 | nc | — |
| A-11 | +14V Main Relay | ECU Power |
| C-11 | nc | — |
| A-12 | Aux 1 | ISC Solenoid |
| C-12 | Trig 1 | Trig 1 |
| A-13 | nc | — |
| C-13 | nc | — |
| A-14 | nc | — |
| C-14 | Trig 2 | Trig 2 |
| A-15 | nc | — |
| C-15 | DI 5 | VTEC Oil Pressure Switch |
| A-16 | Aux 2 | Fuel Pump Relay |
| C-16 | DI 6 | PS Switch |
| A-17 | Aux 3 | A/C Clutch Relay |
| C-17 | nc | — |
| A-18 | Aux 4 | CE Light |
| C-18 | DI 3 | Vehicle Speed |
| A-19 | nc | — |
| C-19 | nc | — |
| A-20 | Ignition 1 | Ignition |
| C-20 | nc | — |
| A-21 | Ignition 2 | Spare |
| C-21 | nc | — |
| A-22 | Ground | — |
| C-22 | nc | — |
| A-23 | Ground | — |
| C-23 | nc | — |
| A-24 | +14V Main Relay | ECU Power |
| C-24 | nc | — |
| A-25 | nc | — |
| C-25 | nc | — |
| A-26 | nc | — |
| C-26 | nc | — |
| A-27 | Injector 6 (Aux) | — |
| C-27 | nc | — |
| A-28 | nc | — |
| C-28 | nc | — |
| A-29 | nc | — |
| C-29 | DI 4 | Clutch Switch (Some models) |
| A-30 | nc | — |
| C-30 | nc | — |
| A-31 | Ignition 3 | Spare |
| C-31 | nc | — |
| A-32 | Ignition 4 | Spare |
| D-1 | An Volt 4 | TPS Signal |
| D-2 | An Temp 2 | ECT |
| D-3 | An Volt 1 | MAP Signal |
| D-4 | +5V Out | — |
| D-5 | DI 7 | Brake Switch |
| D-6 | Knock 1 | Knock |
| D-7 | An Volt 3 | Oxygen Sensor Signal (Primary) |
| D-8 | An Temp 1 | IAT |
| D-9 | nc | — |
| D-10 | +5V Out | — |
| D-11 | Ground (Signal) | — |
| D-12 | Ground (MAP) | — |
| D-13 | Ground (Signal) | — |
| D-14 | An Volt 2 | Oxygen Sensor Signal (Secondary) |
| D-15 | nc | — |
| D-16 | nc | — |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Signal Ground | — |
| 2 | +5V Out | — |
| 3 | An Volt 5 | — |
| 4 | An Volt 6 | — |
| 5 | Aux 7 | — |
| 6 | Aux 8 | — |
| 7 | An Volt 7 | — |
| 8 | An Temp 3 | — |
| 9 | Aux-Ign 5 | — |
| 10 | Aux-Ign 6 | — |
| 11 | Aux-Ign 7 | — |
| 12 | Aux-Ign 8 | — |
| 13 | Digital Input 9 | — |
| 14 | Digital Input 10 | — |
| 15 | An Volt 8 | — |
| 16 | An Volt 9 | — |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |