Autronic SM3 is a standalone or earlier programmable engine-management system. SM3 is described by Autronic as a third-generation ECU with six injector and four ignition outputs. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Processor
Autronic's product page (manufacturer documentation) gives the SM3 microcontroller as a 16-bit Intel part running at 20 MHz. The exact part number is not stated in the sources checked.
Engine applications
The SM3 is a universal ECU, not tied to specific vehicles. Autronic lists reciprocating engines of 1 to 12 cylinders (two-stroke, four-stroke) and two-rotor rotary engines, positioned for high-performance motorsport, with six saturating 3.5 A injector drivers and four push-pull ignition outputs (0.8 A continuous). Autronic warns that fitting it to emission-controlled public-road vehicles is illegal in many markets and that manned-aircraft use is prohibited. No engine codes are listed by the manufacturer.
Wiring and pinout
Consult the Autronic SM3 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
SM3 standard loom connector
The 42 positions of the 42-way main connector, from Autronic's standard loom drawing SM3_0001 revision 1.1 and its numbered input/output function sheet, are on the Autronic SM3 connector pinout page with a redrawn pin-index diagram (diagram redrawn by Tuning Wiki). Autronic's wiring index says the drawing also suits SM3 Marine. The drawing specifies saturated injector drivers and requires ballast for low-impedance injectors, with a minimum 5-ohm load per output. The pin numbers in the outer two connector rows were corrected on an earlier revision of this page and checked against the numbered function sheet.
| Pin | Manufacturer function |
|---|---|
| 1 | Ignition switch input |
| 2 | Switch input 3 |
| 3 | Switch input 2 |
| 4 | Injector output 5 |
| 5 | Ignition output 1 |
| 6 | Ignition output 2 |
| 7 | Output 1 / stepper |
| 8 | Analogue input 1 |
| 9 | Coolant temperature input |
| 10 | HSI input 1 |
| 11 | +8 V trigger supply |
| 12 | Output 8 / tachometer |
| 13 | Output 6 |
| 14 | PWM output 2 |
| 15 | +12 V main supply |
| 16 | Injector output 4 |
| 17 | Injector output 1 |
| 18 | Injector output 6 / switch input 1 |
| 19 | Ignition output 3 |
| 20 | Output 3 / stepper |
| 21 | Throttle position input |
| 22 | Sensor ground |
| 23 | Intake air temperature input |
| 24 | HSI input 2 |
| 25 | Cylinder trigger positive |
| 26 | Sync trigger positive |
| 27 | Output 5 |
| 28 | PWM output 1 |
| 29 | Power supply ground |
| 30 | +12 V RAM supply |
| 31 | Injector output 3 |
| 32 | Injector output 2 |
| 33 | Ignition output 4 |
| 34 | Output 2 / stepper |
| 35 | Output 4 / stepper |
| 36 | +5 V sensor supply |
| 37 | Oxygen sensor input |
| 38 | Analogue input 2 (drawing labels analogue 2–3) |
| 39 | HSI input 3 |
| 40 | Cylinder trigger negative |
| 41 | Sync trigger negative |
| 42 | Output 7 |
Further information
Sources
- Autronic SM3 product page. Manufacturer. Accessed 19 November 2026.
- SM3 standard loom drawing SM3_0001 revision 1.1. Manufacturer. Accessed 19 November 2026.
- SM3 input/output functions. Manufacturer, 12 October 2016. Accessed 19 November 2026.