The 9A9 is an MBE fuel-injection ECU for up to eight cylinders. SBD describes twin wideband lambda inputs and two CAN buses; pinout, sensor and driver suitability depends on the exact hardware and software. Source and identification.
Wiring and pinout
Model wiring documentation: Issue N2, BOM1-010 onward only; obtain the matching diagram for other builds. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete connector assignments
All 121 labelled positions follow the SBD 9A9 connection list, issue N2, BOM 1.010 onward and software 9A9ad400 onward. The table reproduces the source's pin titles; “not named” indicates an empty title, not necessarily an unused circuit. Consult the original for output ratings, pull-ups, individual notes and connector orientation. Assigned functions depend on calibration and particular hardware.
The source describes different functions on earlier BOM revisions at A032, A051, A070 and B102–B105. This table is scoped to BOM 1.010 onward and must not be used to infer an earlier revision.
| Pin | Manufacturer connection-list title |
|---|---|
| A001 | Ground |
| A002 | Ground |
| A003 | ECU Permanent 12V Supply |
| A004 | 12V Switch |
| A005 | 12V Switch |
| A006 | Air Charge Pump Relay |
| A007 | Oil Temp |
| A008 | Injector Drive D (4th to fire) |
| A009 | Anti Lag Signal |
| A010 | Baro Signal |
| A011 | 5Va2 |
| A012 | Injector Drive H (8th to fire) |
| A013 | Narrow Band Oxygen Sensor 1 |
| A014 | Rad Fan Relay 2 |
| A015 | Lambda1 R |
| A016 | Cam Return |
| A017 | EGT Signal |
| A018 | Air Temp Signal |
| A019 | Engine Oil Pressure Signal |
| A020 | Shift Up Solenoid |
| A021 | Ignition Drive E (5th to fire) |
| A022 | Ignition Drive F (6th to fire) |
| A023 | Ignition Drive G (7th to fire) |
| A024 | Ignition Drive H (8th to fire) |
| A025 | Shift Light |
| A026 | Launch Signal |
| A027 | Injector Drive C (3rd to fire) |
| A028 | Not named in source |
| A029 | Lambda1 N |
| A030 | 5Va2 |
| A031 | Injector Drive G (7th to fire) |
| A032 | 0va (YG) |
| A033 | Not named in source |
| A034 | Fuel Pressure Signal |
| A035 | Cam Supply |
| A036 | MAP 2 Signal |
| A037 | Powershift Signal |
| A038 | TPS2 Signal |
| A039 | Not named in source |
| A040 | Egas2 Motor Drive - |
| A041 | Egas2 Motor Drive + |
| A042 | Lambda Sensor 2 Heater |
| A043 | Lambda Sensor 1 Heater |
| A044 | Shift Light 2 |
| A045 | Pedal A Signal |
| A046 | Injector Drive B (2nd to fire) |
| A047 | TPS1 Signal |
| A048 | Lambda1 VG |
| A049 | Lambda1 P |
| A050 | Injector Drive F (6th to fire) |
| A051 | 0Va (ZG) |
| A052 | Rad Fan Relay 1 |
| A053 | Gearbox Signal |
| A054 | Cam 2 Signal |
| A055 | Pedal B Signal |
| A056 | Engine Stop Signal |
| A057 | TPS4 Signal |
| A058 | Down Shift Solenoid |
| A059 | Egas1 Motor Drive - |
| A060 | Egas1 Motor Drive + |
| A061 | Varable Cam 2 Drive |
| A062 | Varable Cam 1 Drive |
| A063 | Neutral Light |
| A064 | Not named in source |
| A065 | Injector Drive A (1st to fire) |
| A066 | MAP Signal |
| A067 | Water Temp Signal |
| A068 | Not named in source |
| A069 | Injector Drive E (5th to fire) |
| A070 | 0Va (XG) |
| A071 | Throttle Blip Solenoid |
| A072 | Narrow Band Oxygen Sensor 2 |
| A073 | Cam1 Signal |
| A074 | TPS3 Signal |
| A075 | Not named in source |
| A076 | Nitrous Input Pin |
| A077 | Not named in source |
| A078 | Not named in source |
| A079 | Wastegate Drive |
| A080 | PWM Water Pump |
| A081 | Tachometer Drive |
| B082 | Not named in source |
| B083 | Lambda2 P |
| B084 | Lambda2 R |
| B085 | Knock1 Signal |
| B086 | Wheelspeed 1 |
| B087 | Wheelspeed 2 |
| B088 | CAN 2 H |
| B089 | CAN H |
| B090 | Fuel Pump Relay |
| B091 | Lambda2 N |
| B092 | Lambda2 VG |
| B093 | Knock1 Return |
| B094 | Wheelspeed 3 |
| B095 | Wheelspeed 4 |
| B096 | CAN 2 L |
| B097 | CAN L |
| B098 | Engine Stop Output |
| B099 | 5Va1 |
| B100 | Crank Signal |
| B101 | Knock 2 Signal |
| B102 | WS1 Ret 0V |
| B103 | WS2 Ret 0V |
| B104 | WS3 Ret 0V |
| B105 | WS4 Ret 0V |
| B106 | PWR Hold Relay |
| B107 | 5Va1 |
| B108 | Crank Return |
| B109 | Knock 2 Return |
| B110 | Ignition Drive A (1st to fire) |
| B111 | Ignition Drive B (2nd to fire) |
| B112 | Ignition Drive C (3rd to fire) |
| B113 | Ignition Drive D (4th to fire) |
| B114 | HSD Battery + |
| B115 | HSD Battery + |
| B116 | Starter Solenoid |
| B117 | Ignition Output |
| B118 | Rad Fan 1 HSD |
| B119 | Fuel Pump |
| B120 | Engine Stop Output |
| B121 | PWM Water Pump |