
The original EMU is a programmable spark-ignition engine ECU predating the EMU Classic. The manufacturer's manual for firmware 0.986 describes speed-density or Alpha-N fuelling, six protected injector outputs, six configurable ignition outputs, six auxiliary outputs, an internal 400 kPa MAP/barometric sensor, two K-type EGT inputs and a Bosch LSU 4.2 wideband input. ECUMaster USA describes the later Classic as using the same software and firmware family while changing the enclosure, 5 V supply, ignition circuitry, H-bridge protection and USB isolation. Original EMU user manual, firmware 0.986 · EMU Classic comparison.
Pinout and identification
The original 0.986 manual gives a device-view diagram with a black and grey connector, both 24 ways. Its black connector lists pin 7 primary trigger, 17 ECU ground and 23 sensor 5 V; its grey connector lists pin 7 injector 1, 18 power 12 V and 24 power ground. Use the full connector table and device-view drawing in the original manual, page 8; check hardware and firmware rather than generalising this to every ECU with an EMU label.
Software
The dated manual describes USB connection to an EMU Windows client and its listed features apply to firmware 0.986. Later firmware and projects may differ. Record the actual serial, hardware and firmware; use current manufacturer downloads and retain the existing calibration before an upgrade. See the ECUMaster model index.
Complete original EMU connector pinout
The manufacturer EMU user manual for firmware 1.1, page 11, provides the device-view orientation and the two complete 24-way tables below. The same-numbered connector on the EMU Black or another unit must not be assumed equivalent. Check the exact hardware, electrical limits and configurable functions in the original.
Black 24-way connector
| Pin | Function in manufacturer manual |
|---|---|
| 1 | EGT input 1 |
| 2 | Knock sensor input 1 |
| 3 | Analogue input 2 |
| 4 | Coolant temperature input |
| 5 | WBO Vs |
| 6 | Cam sync input 2 |
| 7 | Primary trigger input |
| 8 | Ignition coil 5 |
| 9 | EGT input 2 |
| 10 | Knock sensor input 2 |
| 11 | Analogue input 3 |
| 12 | Throttle position input |
| 13 | WBO Ip |
| 14 | Vehicle speed input |
| 15 | Cam sync input 1 |
| 16 | Ignition coil 4 |
| 17 | ECU ground |
| 18 | Sensor ground |
| 19 | Analogue input 4 |
| 20 | Analogue input 1 |
| 21 | Intake air temperature input |
| 22 | WBO Vs/Ip |
| 23 | 5 V supply |
| 24 | Power ground |
Grey 24-way connector
| Pin | Function in manufacturer manual |
|---|---|
| 1 | Ignition coil 6 |
| 2 | Stepper motor 1 winding A |
| 3 | Stepper motor 2 winding A |
| 4 | AUX 6 |
| 5 | AUX 3 |
| 6 | Injector 4 |
| 7 | Injector 1 |
| 8 | Ignition coil 1 |
| 9 | Ignition coil 3 |
| 10 | Stepper motor 1 winding B |
| 11 | Stepper motor 2 winding B |
| 12 | AUX 5 |
| 13 | AUX 2 |
| 14 | Injector 5 |
| 15 | Injector 2 |
| 16 | Ignition coil 2 |
| 17 | Power ground |
| 18 | Power +12 V |
| 19 | WBO heater |
| 20 | AUX 4 / tachometer |
| 21 | AUX 1 |
| 22 | Injector 6 |
| 23 | Injector 3 |
| 24 | Power ground |