Link G1 LinkPlus V14 is a documented G1 Link engine-management designation. Link lists LinkPlus V14 as a G1 ECU for legacy PCLink V2.5. G1 help is provided separately for later Windows releases. Identification source.
Identification and software
Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.
Model-specific wiring
The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.
See Link standalone ECUs for related models and generation distinctions.
Documented V14 breakout loom colours
Link's LinkPlus V14 manual, pages 8–9, identifies these functions and wire colours in the manufacturer breakout loom. This is a colour/function reference, not a numbered connector-cavity map: obtain the matching manual and inspect its wire-side header diagram before identifying positions. Wiring can differ with individual loom and internal configuration. Link staff identified the V14 manual as the relevant reference in their support forum.
The manual's extracted diagram labels Trigger 1 yellow while its separate wire list says white; verify the original connector and build with Link. The manual also varies between yellow/red and yellow/blue in the Aux 2 description; the table follows the colour list, and this connection must be verified before use. Drives and injector assignments depend on firing sequence, trigger and selected injection mode. This table is not verified for V10 or later LinkPlus generations.
| Manufacturer loom function | Wire colour / source note |
|---|---|
| Injector 1 | Brown/Black |
| Injector 2 | Brown |
| Injector 3 | Brown/Red |
| Injector 4 | Brown/Orange |
| Injector 5 | Brown/Yellow |
| Injector 6 | Brown/Green |
| Injector 7 | Brown/Blue |
| Injector 8 | Brown/Purple |
| Ignition 1 | Blue |
| Ignition 2 | Blue/Black |
| Ignition 3 | Blue/White |
| Ignition 4 | Blue/Brown |
| Ignition 5 | Blue/Red |
| Ignition 6 | Blue/Orange |
| Ignition 7 | Blue/Yellow |
| Ignition 8 | Blue/Green |
| Ignition inverted | Pink |
| Power drive A | Orange |
| Power drive B | Orange/Black |
| Idle speed control 1 | Orange/Green |
| Idle speed control 2 | Orange/Blue |
| Wastegate | Orange/Yellow |
| Fuel pump | Purple |
| Shift | White/Black |
| Purge | White/Brown |
| Fan | White/Red |
| Spray | White/Yellow |
| Tachometer | White/Green |
| A/C on | White/Blue |
| Stepper A | Grey |
| Stepper B | Grey/Black |
| Stepper C | Grey/Blue |
| Stepper D | Grey/White |
| Engine temperature | Yellow |
| Air temperature | Yellow/Black |
| Throttle position | Yellow/Orange |
| A/C request | Yellow/Red |
| MAP | Yellow/Brown |
| Oxygen | White |
| Aux input 1 | Yellow/Green |
| Aux input 2 | Yellow/Blue |
| Power in | Red |
| +5V output | Red/Blue |
| +12V sensor output | Red or green in trigger cables |
| Signal ground | Black |
| Power ground | Black |
| Knock 1 | Red, screened cable |
| Knock 2 | Red, screened cable |
| Trigger 1 | Conflicting source labels: yellow or white, screened cable |
| Trigger 2 | Blue, screened cable |
The manual specifies group-fire operation using injector drivers 7 and 8, and describes ballast selection by injector resistance and delivery mode. Follow the original guide for the actual installation.