Overview and hardware
Syvecs S6GP is a British engine-management ECU. Legacy general-purpose S6 wire-in ECU. The manufacturer guide identifies INJ1 pin 1, sensor ground pin 7, 5VOUT1 pin 10, knock pin 17 and IGN1–IGN5 pins 26–30; examples depend on configuration. Consult the full guide for connector orientation and assignments.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S6GP wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
The following positions are from the Syvecs S6GP wiring guide. N/A reproduces the guide's unavailable label. Function examples can be reassigned; identify the connector view, build options and current limits in the original before wiring.
| Pin | Source label | Example function |
|---|---|---|
| 1 | INJ1 | CYL 1 INJECTOR |
| 2 | FUEL9 | FUEL PUMP |
| 3 | FUEL10 | SPARE OUTPUT |
| 4 | FUEL11 | BOOST SOLENOID |
| 5 | FUEL12 | TACHO OUTPUT |
| 6 | ANGND1 | TRIGGER GROUND |
| 7 | ANGND1 | SENSOR GND |
| 8 | ANGND2 | ABS GROUNDS |
| 9 | ANGND2 | CAL SWITCH GROUNDS |
| 10 | 5VOUT1 | 5V OUTPUT FOR SENSORS |
| 11 | 5VOUT2 | SPARE 5V OUTPUT |
| 12 | 12VOUT | SPARE 12V OUTPUT |
| 13 | FUEL13 | IDLE STEPPER |
| 14 | FUEL14 | IDLE STEPPER |
| 15 | FUEL15 | IDLE STEPPER |
| 16 | FUEL16 | IDLE STEPPER |
| 17 | KNOCK | KNOCK SENSOR INPUT |
| 18 | KNKGND | KNOCK SENSOR GROUND |
| 19 | VBAT | 12V IGNITION SUPPLY FOR ECU |
| 20 | VBAT | 12V IGNITION SUPPLY FOR ECU |
| 21 | VBAT | 12V IGNITION SUPPLY FOR ECU |
| 22 | INJ6 | CYL 6 INJECTOR |
| 23 | INJ8 | CYL 8 INJECTOR |
| 24 | INJ2 | CYL 2 INJECTOR |
| 25 | INJ3 | CYL 3 INJECTOR |
| 26 | IGN1 | CYL 1 IGNITION OUTPUT |
| 27 | IGN2 | CYL 2 IGNITION OUTPUT |
| 28 | IGN3 | CYL 3 IGNITION OUTPUT |
| 29 | IGN4 | CYL 4 IGNITION OUTPUT |
| 30 | IGN5 | CYL 5 IGNITION OUTPUT |
| 31 | IGN6 | CYL 6 IGNITION OUTPUT |
| 32 | COMGND | COMMUNICATION GND |
| 33 | LAMV | LAMV |
| 34 | LAMGND | LAM GND |
| 35 | AB1 (#1) | CAM SENSOR INPUT |
| 36 | AB2 (#2) | CRANK SENSOR INPUT |
| 37 | AB3 (#3) | FL SPEED INPUT |
| 38 | AB4 (#4) | RL SPEED INPUT |
| 39 | THER+ | EGT + |
| 40 | AV1 (#9) | TPS INPUT |
| 41 | AV2 (#10) | MAP INPUT |
| 42 | AV3 (#11) | SPARE INPUT |
| 43 | AV4 (#12) | SPARE INPUT |
| 44 | PWRGND | ECU GND |
| 45 | PWRGND | ECU GND |
| 46 | INJ7 | CYL 7 INJECTOR |
| 47 | PWRGND | ECU GND |
| 48 | INJ4 | CYL 4 INJECTOR |
| 49 | LANTX‐ | Cat5 Pin6 |
| 50 | LANTX+ | Cat5 Pin3 |
| 51 | LANRX‐ | Cat5 Pin2 |
| 52 | LANRX+ | Cat5 Pin1 |
| 53 | CANH | CANH |
| 54 | CANL | CANL |
| 55 | RS232RX | RS232RX |
| 56 | RS232TX | RS232TX |
| 57 | LAMI | LAMI |
| 58 | AU1 (#5) | VEHICLE SPEED INPUT |
| 59 | AU2 (#6) | SPARE INPUT |
| 60 | AU3 (#7) | SPARE INPUT |
| 61 | AU4 (#8) | SPARE INPUT |
| 62 | THER- | EGT ‐ |
| 63 | AR1 (#13) | COOLANT TEMP INPUT |
| 64 | AR2 (#14) | AIR TEMP INPUT |
| 65 | AR3 (#15) | CALIBRATION SWITCH INPUT |
| 66 | AR4 (#16) | SPARE INPUT |
| 67 | PWRGND | PWR GND |
| 68 | PWRGND | PWR GND |
| 69 | INJ5 | CYL 5 INJECTOR |
| 70 | PWRGND | PWR GND |
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.