Autronic SM3MR is a standalone or earlier programmable engine-management system. Marine version of the SM3 family; identify its case and exact firmware and consult the marine product's wiring reference. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Processor
Autronic's SM3MR product page (manufacturer documentation) gives a 16-bit Intel microprocessor running at 20 MHz. The exact part number is not stated in the sources checked.
Engine applications
The SM3MR is a universal marine and motorsport ECU rather than a vehicle-specific unit. Autronic's specification table lists 1 to 8, 10 and 12 cylinders plus two-rotor rotary engines (the page overview says 1 to 16 cylinders, which conflicts with the table; the table is the more specific statement). Outputs include six saturating 3.5 A injector drivers, four push-pull ignition outputs, eight general-purpose outputs and two dedicated PWM outputs, with a 42-way sealed main connector and an 8 mm 3-way sealed serial connector. Autronic warns against emission-controlled road use in many markets and prohibits manned-aircraft use. No engine codes are listed.
Wiring and pinout
Consult the Autronic SM3MR wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
SM3 standard loom connector
The 42 positions of the standard SM3 loom drawing, which Autronic's wiring index says also suits SM3 Marine, are on the Autronic SM3 connector pinout page with a redrawn pin-index diagram (diagram redrawn by Tuning Wiki from Autronic drawing SM3_0001 revision 1.1). Confirm connector orientation and actual ECU configuration before wiring; the pin numbers in the outer two rows were corrected against Autronic's numbered input/output function sheet.
| Pin | Manufacturer function |
|---|---|
| 1 | Ignition switch input |
| 2 | Switch input 3 |
| 3 | Switch input 2 |
| 4 | Injector output 5 |
| 5 | Ignition output 1 |
| 6 | Ignition output 2 |
| 7 | Output 1 / stepper |
| 8 | Analogue input 1 |
| 9 | Coolant temperature input |
| 10 | HSI input 1 |
| 11 | +8 V trigger supply |
| 12 | Output 8 / tachometer |
| 13 | Output 6 |
| 14 | PWM output 2 |
| 15 | +12 V main supply |
| 16 | Injector output 4 |
| 17 | Injector output 1 |
| 18 | Injector output 6 / switch input 1 |
| 19 | Ignition output 3 |
| 20 | Output 3 / stepper |
| 21 | Throttle position input |
| 22 | Sensor ground |
| 23 | Intake air temperature input |
| 24 | HSI input 2 |
| 25 | Cylinder trigger positive |
| 26 | Sync trigger positive |
| 27 | Output 5 |
| 28 | PWM output 1 |
| 29 | Power supply ground |
| 30 | +12 V RAM supply |
| 31 | Injector output 3 |
| 32 | Injector output 2 |
| 33 | Ignition output 4 |
| 34 | Output 2 / stepper |
| 35 | Output 4 / stepper |
| 36 | +5 V sensor supply |
| 37 | Oxygen sensor input |
| 38 | Analogue input 2 (drawing labels analogue 2–3) |
| 39 | HSI input 3 |
| 40 | Cylinder trigger negative |
| 41 | Sync trigger negative |
| 42 | Output 7 |
Further information
Sources
- Autronic SM3MR product page. Manufacturer. Accessed 19 November 2026.
- SM3 standard loom drawing SM3_0001 revision 1.1. Manufacturer. Accessed 19 November 2026.