
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Ford Focus RS Mk3 SGDI4, with product code SGDI-RSMK3. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Confirmed installation details
SGDI-RSMK3 is listed for the Ford Focus RS Mk3. The kit supports direct injection and additional port injection subject to calibration. The manual describes the drive mode selector being used for calibration selection, and gives a complete loom-to-ECU schedule.
The documented S8-based connector schedule includes pin 1 power ground, pin 8 as a configurable input, and pin 22 as a fuel-pump relay output. The manual describes repurposing other outputs for supplementary injectors only after calibration has been updated. Check the exact product and loom version.
Wiring and pinout
Syvecs Ford Focus RS Mk3 SGDI4 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Ford Focus RS Mk3 SGDI4 product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer loom-to-ECU connector schedule
From pages 5–6 of the Syvecs Ford Focus RS Mk3 kit manual. This chart lists the Syvecs ECU pins alongside corresponding loom positions and manufacturer notes; a dash reproduces a blank in the source and does not prove a circuit is unused. Confirm the ECU and vehicle harness revision, connector view and calibration before use.
| Syvecs pin | Syvecs function | Focus RS loom pin / wire | Focus function |
|---|---|---|---|
| 1 | POWER GROUND | B98 | Power Ground |
| 2 | IGNITION #08 | E43 | Ign 4 |
| 3 | IGNITION #07 | E72 | Ign 3 |
| 4 | IGNITION #06 | E57 | Ign 2 |
| 5 | IGNITION #05 | E42 | Ign 1 |
| 6 | FUEL #10 | B23 | Cooling Fan |
| 7 | KNOCK #02 | E50 | Knock 2 |
| 8 | INPUT #16 (5V/TH/BI/FREQ) | Customer to Wire in | Flex Fuel |
| 9 | INPUT #14 (5V/TH/BI/FREQ) | E36 | ECT |
| 10 | INPUT #12 (5V/TH/BI/FREQ) | B6 | Clutch Top |
| 11 | INPUT #10 (5V/TH/BI/FREQ) | E28 | intake CAM |
| 12 | THERMO - #02 | — | Spare EGT- |
| 13 | THERMO + #02 | — | Spare EGT+ |
| 14 | INPUT #07 (5V/TH/BI/FREQ) | B30 | Clutch Bottom |
| 15 | INPUT #05 (5V/TH/BI/FREQ) | B31 | Reverse Sw |
| 16 | INPUT #03 (5V/TH/BI/FREQ) | E46 | Cylinder Head temp2 |
| 17 | INPUT #01 (5V/TH/BI/FREQ) | B52 | AC Pressure |
| 18 | LAMBDA V #01 | E64 | Lambda V |
| 19 | INPUT #21 (TH) | B72 | Crank case pressure |
| 20 | FUEL #15 | B20 | Canister Purge |
| 21 | RS232#1TX | — | — |
| 22 | FUEL #07 | B39 | fuel pump relay |
| 23 | FUEL #05 | B4 | Cooling Fan high speed |
| 24 | IGN4 | E85 | GDI 4+ (spare) |
| 25 | IGN3 | E82 | GDI 3+ |
| 26 | IGN2 | E83 | GDI 2+ |
| 27 | IGN1 | E84 | GDI 1+ |
| 28 | POWER GROUND | Custom | Can Bridge Ground |
| 29 | POWER GROUND | B97 | Power Ground |
| 30 | FUEL #14 | E29 | VVT exhaust |
| 31 | FUEL #13 | E1 | VVT intake 1 |
| 32 | FUEL #12 / GDI PUMP - | E77 | Fuel Vol contrl -ve |
| 33 | FUEL #11 | E14 | Lambda Heater |
| 34 | FUEL #09 | E3 | Wastegate Recirc |
| 35 | KNOCK #01 | E65 | Knock 1 |
| 36 | INPUT #15 (5V/TH/BI/FREQ) | B55 | PPS1 |
| 37 | INPUT #13 (5V/TH/BI/FREQ) | B54 | PPS2 |
| 38 | INPUT #11 (5V/TH/BI/FREQ) | E54 | exhaust CAM |
| 39 | INPUT #09 (5V/TH/BI/FREQ) | E11 | Crank |
| 40 | THERMO - #01 | — | Spare EGT- |
| 41 | INPUT #08 (5V/TH/BI/FREQ) | E33 | Map |
| 42 | INPUT #06 (5V/TH/BI/FREQ) | B66 | Brake |
| 43 | INPUT #04 (5V/TH/BI/FREQ) | Spare | Spare Input |
| 44 | INPUT #02 (5V/TH/BI/FREQ) | E37 | Direct Injection pressure |
| 45 | CAN LO #03 | — | — |
| 46 | INPUT #22 (TH) | Spare | Spare Input |
| 47 | FUEL #16 | B43 | Starter Ground |
| 48 | RS232 RX | — | — |
| 49 | FUEL #08 | B2 | A/C Clutch |
| 50 | FUEL #06 | B80 | Exhaust Solenoid PWM |
| 51 | FUEL #04 | E92 | GDI 4- |
| 52 | FUEL #03 | E93 | GDI 3- |
| 53 | FUEL #02 | E88 | GDI 2- |
| 54 | FUEL #01 | E87 | GDI 1- |
| 55 | POWER GROUND | B96 | Power Ground |
| 56 | BATTERY SUPPLY | — | VBATT + Can Bridge 12V |
| 57 | BATTERY SUPPLY | B102 | VBATT |
| 58 | H-BRIDGE #01 | E86 | DBW+ |
| 59 | H-BRIDGE #02 | E91 | DBW- |
| 60 | H-BRIDGE #03 | E16 | Boost solenoid |
| 61 | H-BRIDGE #04 | E78 | Fuel Vol Cntrl +ve |
| 62 | 10V OUT | — | — |
| 63 | 5V OUT #02 | E6, E7, E8 | 5V Out |
| 64 | 5V OUT #01 | B10, B11, B12, B13 | 5V Out |
| 65 | KNOCK GROUND | E66, E51 | — |
| 66 | INPUT #20 (5V/KNOCK #04) | B71 | Fuel Supply pressure |
| 67 | SENSOR GROUND #02 | B7, B16 B18 | AN Ground |
| 68 | INPUT #19 (5V/KNOCK #03) | Spare | Spare Input |
| 69 | SENSOR GROUND #01 | E53 | AN Ground |
| 70 | THERMO + #01 | — | Spare EGT+ |
| 71 | INPUT #18 (5V) | E52 | TPS2 |
| 72 | SENSOR GROUND #02 | B35, B36 | AN Ground |
| 73 | INPUT #17 (5V) | E68 | TPS1 |
| 74 | SENSOR GROUND #01 | E31, E20 | AN Ground |
| 75 | CAN HI #03 | — | — |
| 76 | LAMBDA I #01 | E63 | — |
| 77 | LAMBDA GROUND | E49 | — |
| 78 | COMMS GROUND | — | — |
| 79 | CAN LO #02 | — | — |
| 80 | CAN HI #02 | — | — |
| 81 | CAN LO #01 | GT150-C | — |
| 82 | CAN HI #01 | GT150-D | — |
| 83 | INPUT #24 (TH) | Spare | Spare Input |
| 84 | INPUT #23 (TH) | E34 | ACT |
| 85 | LANRX+ | White/orange | Ethernet Socket, 0.3m |
| 86 | LANRX- | ORANGE/white | — |
| 87 | LANTX+ | White/Green | — |
| 88 | LANTX- | GREEN/white | — |