Tuning Wiki
Golf Mk7.5 R S7D plug-in ECU
Golf Mk7.5 R S7D plug-in ECU. Image: Syvecs product page, reproduced with permission.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.5 R GTI E888 Gen3 S7D, with product code S7D-VW7.5RDF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Golf Mk7.5 R GTI E888 Gen3 S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

MQB4 S7D ECU and accessory connector schedules

The Syvecs MQB4 S7D kit manual identifies ECU connectors A–D and a separate 26-way accessory connector. These are ECU or accessory connector positions and documented functions, not OEM factory connector cavity numbers. Check the correct kit, wiring, electrical limits, ECU variant and connector orientation before applying them.

Source conflicts: In the same document B2/B3 are labelled CAN2 low/high but their OEM-function column says K-type thermocouple; accessory B14/B15 are labelled CAN3 low/high but the notes also say K-type EGT. The second lambda labels duplicate several first-lambda names and the B18 OEM column says Slave Out 10. The entries below preserve the document and require confirmation with Syvecs rather than an assumed correction.

A connector

TerminalSyvecs labelFunction / OEM note in source
A1PWR CTR OUTMain relay output
A2H-Bridge1H-Bridge1
A3H-Bridge2H-Bridge2
A4H-Bridge3H-Bridge3
A5H-Bridge4H-Bridge4
A6H-Bridge5H-Bridge5
A7H-Bridge6H-Bridge6
A8H-Bridge7H-Bridge7
A9H-Bridge8H-Bridge8
A10GDI LS1Port injector 1; fuel 1 / low-side GDI 1
A11GDI LS2DI injector 1−
A12GDI LS3Port injector 2; fuel 3 / low-side GDI 3
A13GDI LS4DI injector 2−
A14GDI LS5Port injector 3; fuel 5 / low-side GDI 5
A15GDI LS6DI injector 3−
A16GDI LS7Port injector 4; fuel 7 / low-side GDI 7
A17GDI LS8DI injector 4−
A18GDI HS1/2DI injector 1+
A19GDI HS3/4DI injector 2+
A20GDI Pump 1 HSDI pump high side
A21GDI HS5/6DI injector 3+
A22GDI HS7/8DI injector 4+
A23GDI Pump 2 HSNC in OEM function column
A24GDI Pump 1 LowSideFuel 15 output
A25Fuel 16Fuel 16 output
A26IGN1Cylinder 1 ignition output
A27IGN2Cylinder 2 ignition output
A28IGN3Cylinder 3 ignition output
A29IGN4Cylinder 4 ignition output
A30IGN5DI pump low
A31IGN6Tacho sync
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

B connector

TerminalSyvecs labelFunction / OEM note in source
B1PWRGNDPower ground
B2CAN2 LCAN 2; OEM column says K-type thermo
B3CAN2 HCAN 2; OEM column says K-type thermo
B4KNOCK 1Knock 1
B5KNOCK 2Knock 2
B6PVBATConstant 12 V
B7IVBAT12 V
B8LAM1ALamV / LamD1+ / LamLun1
B9LAM1BLamI / LamD1− / LamIP1
B10LAM1CLamLIA1
B11LAM1DLamGND / LamLVM1
B12LAM1HEATERLambda heater
B13IVBAT12 V
B14LAM2ALamV / LamD1+ / LamLun1
B15LAM2BLamI / LamD1− / LamIP1
B16LAM2CLamLIA1
B17LAM2DLamGND / LamLVM1
B18LAM2HEATERLambda heater; OEM column says Slave Out 10
B19IVBAT12 V
B20KLINEK-line
B21RS232RXRS232 RX
B22RS232TXRS232 TX
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

C connector

TerminalSyvecs labelFunction / OEM note in source
C1KNOCKGNDKnock ground
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT5 V output
C65V OUT5 V output
C75V OUT5 V output
C8CAN1 LCAN 1 low
C9CAN1 HCAN 1 high
C10AN01Bipolar input
C11AN02Bipolar input
C12AN03Bipolar input
C13AN04Bipolar input
C14AN05Unipolar input
C15AN06Unipolar input
C16AN07Unipolar input
C17AN08Unipolar input
C18AN09Voltage input
C19AN10Voltage input
C20AN11Voltage input
C21AN12Voltage input
C22AN13Resistive input
C23AN14Resistive input
C24AN15Resistive input
C25AN16Resistive input
C26EGT1−EGT 1 negative
C27EGT1+EGT 1 positive
C28PWR CTR INMain relay input switch
C29AN S1Unipolar input
C30AN S2Unipolar input
C31AN S3Unipolar input
C32AN S4Unipolar input
C33AN S5Unipolar input
C34AN S6Unipolar input

D connector

TerminalSyvecs labelFunction / OEM note in source
D1DVBAT1GDI power supply
D2DVBAT2GDI power supply
D3DVBAT3GDI power supply
D4DVBAT4GDI power supply
D5FUEL9PWM / fuel output
D6FUEL10PWM / fuel output
D7FUEL11PWM / fuel output
D8FUEL12PWM / fuel output
D9FUEL13PWM / fuel output
D10FUEL14PWM / fuel output
D11LSO1PWM output
D12LSO2PWM output
D13LSO3PWM output
D14LSO4PWM output
D15LSO5PWM output
D16LSO6PWM output
D17EGT2−EGT 2 negative
D18EGT2+EGT 2 positive
D19NCNC in source
D20NCNC in source
D21NCNC in source
D22NCNC in source
D23CAN3LCAN 3 low
D24CAN3HCAN 3 high
D25PWRGNDPower ground
D26PWRGNDPower ground

Accessory connector

TerminalSyvecs labelFunction / OEM note in source
B1Ground
B2HBR3
B3HBR4
B4HBR5
B5Fuel15
B6Fuel16
B712 V
B8LAMHtr2
B9CAN2LSpare CAN
B10CAN2HSpare CAN
B11RS232RX
B12RS232TX
B13LAM2ASpare input S1AN10
B14CAN3LK-type EGT (as written in source)
B15CAN3HK-type EGT (as written in source)
B16Lam2CSpare input S1AN11
B17EGT1−
B18EGT1+
B19AN15Spare input
B20S1AN04
B21ANGroundSensor ground
B225 V5 V output for sensors
B23LANRX−Ethernet
B24LANRX+Ethernet
B25LANTX−Ethernet
B26LANTX+Ethernet

Directly applicable articles

Technical articles assigned to this context will appear here.