The spark plug is the last link in the ignition chain and the first part to show what the combustion chamber is doing. This page covers heat range, gap and reading plugs on a modified or boosted engine. Spark timing itself is on ignition tuning.
Heat range
A plug tip normally runs between 500 and 800 °C (Wikipedia: Spark plug). A hot plug insulates the tip and retains heat; a cold plug conducts heat away. If the tip is too hot it can cause pre-ignition or knocking, which can damage the engine. If it is too cold it can form conductive deposits that waste or short out the spark energy.
Numbering differs between makers. Denso and NGK use higher numbers for colder plugs, while Champion, Bosch, BRISK, Beru and ACDelco use higher numbers for hotter ones, so the numbers cannot be compared across brands.
What boost and power changes
Modifications that add power generally raise engine and plug temperatures, and a plug for a modified engine has to be established by testing. NGK's guidance for forced induction is one heat range colder for every 75 to 100 hp added, or when compression is significantly raised. It also calls for slightly retarded timing, more fuel enrichment and higher octane, and warns that failing to address all of these virtually guarantees engine damage (NGK Australia: modified and performance engines). Treat that as a rule of thumb, not a calibration; the engine builder and tuner set the real figures.
More is not always colder. Cars making 1,000 hp or less can use a slightly colder plug, but one that is much colder causes idle misfires and drivability problems, and boosted drag cars making over 2,000 hp need a hotter plug (Performance Racing Industry). Check with the plug maker.
Gap
Typical automotive gaps are 0.6 to 1.8 mm. A narrow gap gives a weak spark, and a wide gap may misfire at high speed. Boost raises cylinder pressure, and a higher pressure makes it harder for the spark to jump the gap with the same coil voltage, so boosted engines usually run a smaller gap. Suggested figures are 0.028 to 0.032 in for street cars making 600 to 800 hp, and 0.018 to 0.022 in for higher-power engines, on the assumption that coil voltage is unchanged. Those are figures for high-power US-style engines, not general specifications.
Gapping must be done carefully. Adjusting the gap is not recommended for iridium or platinum plugs because the welded metal disc can be damaged, and the proper tool should be used gently. Check the plug maker's instructions, and on a modern coil-on-plug engine check what the ignition system can deliver at the smaller gap.
Other details that matter
- Tip style. Projected or non-projected tip style must match the cylinder head, and a mismatch causes misfires and lost power. A plug that protrudes too far can be struck by the piston.
- Resistor plugs. Plugs with and without resistors look alike, and modern electronics need resistor plugs, because a missing resistor can disturb data loggers and radios.
- Electrode material. Iridium, platinum and other noble metals resist erosion and allow a smaller centre electrode. Tip material is generally not a concern for boosted engines, though copper wears faster.
- Leads and coils. Plug wires should be replaced regularly. Weak coils and leads show up as misfire first at high load.
Reading the plug
Test in stages: half throttle, then three-quarter throttle, then full throttle, inspecting the plugs after each stage. A very black insulator nose suggests the plug is running cool and carbon is not burning off. A very clean, white nose suggests the plug is nearing its upper temperature limit, where the nose can blister and the ground electrode melt. A plug reading is evidence about temperature; it is not a mixture measurement. Use a wideband sensor for that: air-fuel ratio and wideband lambda sensors.
A plug does not fix the cause
A slightly hotter plug can hide poor oil control, and changing heat range can mask a serious fault. Detonation, a lean mixture or too much advance should be corrected at the source: engine knock and fuel system upgrades. A fouled or damaged plug also tells you about the oil and fuel the engine is seeing, as covered on common petrol engine problems. Spark plug testing equipment is on spark and ignition testers.
Sources
- Modified and Performance Engines. NGK Spark Plugs Australia. Plug temperature range, forced-induction heat range rule and plug reading. Accessed 2026-11-19.
- PRI Tech: Spark Plugs For Boosted Engines. Erik Radzins, Performance Racing Industry, 1 January 2023. Heat range, gap, tip style and resistor plugs. Accessed 2026-11-19.
- Spark plug. Wikipedia. Heat range, brand numbering, gap, materials and overheating. Accessed 2026-11-19.