
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.1 R GTI E888 Gen3 S7D, with product code S7D-VW7RDF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Golf Mk7.1 R GTI E888 Gen3 S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Golf Mk7.1 R GTI E888 Gen3 S7D product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
MQB4 S7D ECU and accessory connector schedules
The Syvecs MQB4 S7D kit manual identifies ECU connectors A–D and a separate 26-way accessory connector. These are ECU or accessory connector positions and documented functions, not OEM factory connector cavity numbers. Check the correct kit, wiring, electrical limits, ECU variant and connector orientation before applying them.
Source conflicts: In the same document B2/B3 are labelled CAN2 low/high but their OEM-function column says K-type thermocouple; accessory B14/B15 are labelled CAN3 low/high but the notes also say K-type EGT. The second lambda labels duplicate several first-lambda names and the B18 OEM column says Slave Out 10. The entries below preserve the document and require confirmation with Syvecs rather than an assumed correction.
A connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| A1 | PWR CTR OUT | Main relay output |
| A2 | H-Bridge1 | H-Bridge1 |
| A3 | H-Bridge2 | H-Bridge2 |
| A4 | H-Bridge3 | H-Bridge3 |
| A5 | H-Bridge4 | H-Bridge4 |
| A6 | H-Bridge5 | H-Bridge5 |
| A7 | H-Bridge6 | H-Bridge6 |
| A8 | H-Bridge7 | H-Bridge7 |
| A9 | H-Bridge8 | H-Bridge8 |
| A10 | GDI LS1 | Port injector 1; fuel 1 / low-side GDI 1 |
| A11 | GDI LS2 | DI injector 1− |
| A12 | GDI LS3 | Port injector 2; fuel 3 / low-side GDI 3 |
| A13 | GDI LS4 | DI injector 2− |
| A14 | GDI LS5 | Port injector 3; fuel 5 / low-side GDI 5 |
| A15 | GDI LS6 | DI injector 3− |
| A16 | GDI LS7 | Port injector 4; fuel 7 / low-side GDI 7 |
| A17 | GDI LS8 | DI injector 4− |
| A18 | GDI HS1/2 | DI injector 1+ |
| A19 | GDI HS3/4 | DI injector 2+ |
| A20 | GDI Pump 1 HS | DI pump high side |
| A21 | GDI HS5/6 | DI injector 3+ |
| A22 | GDI HS7/8 | DI injector 4+ |
| A23 | GDI Pump 2 HS | NC in OEM function column |
| A24 | GDI Pump 1 LowSide | Fuel 15 output |
| A25 | Fuel 16 | Fuel 16 output |
| A26 | IGN1 | Cylinder 1 ignition output |
| A27 | IGN2 | Cylinder 2 ignition output |
| A28 | IGN3 | Cylinder 3 ignition output |
| A29 | IGN4 | Cylinder 4 ignition output |
| A30 | IGN5 | DI pump low |
| A31 | IGN6 | Tacho sync |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
B connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2 L | CAN 2; OEM column says K-type thermo |
| B3 | CAN2 H | CAN 2; OEM column says K-type thermo |
| B4 | KNOCK 1 | Knock 1 |
| B5 | KNOCK 2 | Knock 2 |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | LamV / LamD1+ / LamLun1 |
| B9 | LAM1B | LamI / LamD1− / LamIP1 |
| B10 | LAM1C | LamLIA1 |
| B11 | LAM1D | LamGND / LamLVM1 |
| B12 | LAM1HEATER | Lambda heater |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | LamV / LamD1+ / LamLun1 |
| B15 | LAM2B | LamI / LamD1− / LamIP1 |
| B16 | LAM2C | LamLIA1 |
| B17 | LAM2D | LamGND / LamLVM1 |
| B18 | LAM2HEATER | Lambda heater; OEM column says Slave Out 10 |
| B19 | IVBAT | 12 V |
| B20 | KLINE | K-line |
| B21 | RS232RX | RS232 RX |
| B22 | RS232TX | RS232 TX |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
C connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| C1 | KNOCKGND | Knock ground |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | 5 V output |
| C6 | 5V OUT | 5 V output |
| C7 | 5V OUT | 5 V output |
| C8 | CAN1 L | CAN 1 low |
| C9 | CAN1 H | CAN 1 high |
| C10 | AN01 | Bipolar input |
| C11 | AN02 | Bipolar input |
| C12 | AN03 | Bipolar input |
| C13 | AN04 | Bipolar input |
| C14 | AN05 | Unipolar input |
| C15 | AN06 | Unipolar input |
| C16 | AN07 | Unipolar input |
| C17 | AN08 | Unipolar input |
| C18 | AN09 | Voltage input |
| C19 | AN10 | Voltage input |
| C20 | AN11 | Voltage input |
| C21 | AN12 | Voltage input |
| C22 | AN13 | Resistive input |
| C23 | AN14 | Resistive input |
| C24 | AN15 | Resistive input |
| C25 | AN16 | Resistive input |
| C26 | EGT1− | EGT 1 negative |
| C27 | EGT1+ | EGT 1 positive |
| C28 | PWR CTR IN | Main relay input switch |
| C29 | AN S1 | Unipolar input |
| C30 | AN S2 | Unipolar input |
| C31 | AN S3 | Unipolar input |
| C32 | AN S4 | Unipolar input |
| C33 | AN S5 | Unipolar input |
| C34 | AN S6 | Unipolar input |
D connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| D1 | DVBAT1 | GDI power supply |
| D2 | DVBAT2 | GDI power supply |
| D3 | DVBAT3 | GDI power supply |
| D4 | DVBAT4 | GDI power supply |
| D5 | FUEL9 | PWM / fuel output |
| D6 | FUEL10 | PWM / fuel output |
| D7 | FUEL11 | PWM / fuel output |
| D8 | FUEL12 | PWM / fuel output |
| D9 | FUEL13 | PWM / fuel output |
| D10 | FUEL14 | PWM / fuel output |
| D11 | LSO1 | PWM output |
| D12 | LSO2 | PWM output |
| D13 | LSO3 | PWM output |
| D14 | LSO4 | PWM output |
| D15 | LSO5 | PWM output |
| D16 | LSO6 | PWM output |
| D17 | EGT2− | EGT 2 negative |
| D18 | EGT2+ | EGT 2 positive |
| D19 | NC | NC in source |
| D20 | NC | NC in source |
| D21 | NC | NC in source |
| D22 | NC | NC in source |
| D23 | CAN3L | CAN 3 low |
| D24 | CAN3H | CAN 3 high |
| D25 | PWRGND | Power ground |
| D26 | PWRGND | Power ground |
Accessory connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| B1 | Ground | |
| B2 | HBR3 | |
| B3 | HBR4 | |
| B4 | HBR5 | |
| B5 | Fuel15 | |
| B6 | Fuel16 | |
| B7 | 12 V | |
| B8 | LAMHtr2 | |
| B9 | CAN2L | Spare CAN |
| B10 | CAN2H | Spare CAN |
| B11 | RS232RX | |
| B12 | RS232TX | |
| B13 | LAM2A | Spare input S1AN10 |
| B14 | CAN3L | K-type EGT (as written in source) |
| B15 | CAN3H | K-type EGT (as written in source) |
| B16 | Lam2C | Spare input S1AN11 |
| B17 | EGT1− | |
| B18 | EGT1+ | |
| B19 | AN15 | Spare input |
| B20 | S1AN04 | |
| B21 | ANGround | Sensor ground |
| B22 | 5 V | 5 V output for sensors |
| B23 | LANRX− | Ethernet |
| B24 | LANRX+ | Ethernet |
| B25 | LANTX− | Ethernet |
| B26 | LANTX+ | Ethernet |