Tuning Wiki

SCS lists Tornado 2 separately in its obsolete 2008–2015 hardware programme and identifies Delta 700 as its replacement, with a connector change required. An archived S65 installation is reported for a Tornado 2, but this example does not prove compatibility with all S65 engines or harnesses. Manufacturer or supplier evidence.

Identification, software and support

Record the complete ECU label, hardware revision, original application, connector type and current calibration. SCS identifies the older Typhoon, Tornado, Storm and Hurricane families with its final SXT Legacy software. Its newer Delta devices use the current SXTune release. The availability of calibration migration does not mean the same project should be written to different hardware without conversion. SCS software downloads · manufacturer upgrade notes.

Model-specific wiring

A third-party display interface guide identifies Tornado 2 connector A pin 21 as CAN high and pin 22 as CAN low. It links a Tornado V3 diagram; this identifies communications only and is not a full engine-harness pinout. Confirm the exact unit and get the original loom diagram. PLEX Tornado 2 connection guide.

Replacement and calibration

SCS identifies Delta 700 as the replacement for this model in its trade-in list. Consult SCS about ECU-specific connector changes, harness, software and calibration before making any conversion. See the SCS model index for the separate Delta reference.

Manufacturer connector schedules

The manufacturer’s SXTune user manual, revision 4, identifies Typhoon 2 and Tornado 2 and documents a common 35-way connector and a second 23-way Tornado connector. This archive is a copy of the Specialist Components manual. Verify the ECU label, hardware and application against the original diagrams before wiring.

35-way ECU connector

PinNameFunctionSource notes
1VBATTBattery voltage direct6–15 V direct power
2VKEYIgnition key inputSwitched ignition feed
3GROUNDPower ground—
4INJ1Injector 15 A protected output
5INJ2Injector 25 A protected output
6INJ3Injector 35 A protected output
7INJ4Injector 45 A protected output
8DIG_GNDCrank/cam sensor groundDigital ground
9CRANKCrank sensorHall or variable reluctance
10CAM1Inlet camshaft sensor, bank 1Hall or variable reluctance
11TCOOLCoolant temperature input0–5 V analogue
12TAIRAir temperature input0–5 V analogue
13IGN1Ignition coil 1Power or TTL; hardware-selected
14IGN2Ignition coil 2Power or TTL; hardware-selected
15IGN3Ignition coil 3Power or TTL; hardware-selected
16IGN4Ignition coil 4Power or TTL; hardware-selected
17LINEAR1Analogue input 1Configurable 0–5 V
18CAM2Inlet camshaft sensor, bank 2Hall or variable reluctance
19NTC_GND1Temperature sensor groundAnalogue ground
20LAMBDA1Lambda sensor bank 10–5 V analogue
21CANHCAN highTo PC communications DB9
22CANLCAN lowTo PC communications DB9
23PROGProgram enableTo PC communications DB9
24RELAY1Relay outputConfigurable function
25RELAY2Fuel pump relay outputFuel pump and O2 heater relay
26PWM1PWM output 1Configurable; 5 A protected
27PWM2PWM output 2Configurable; 5 A protected
28AUX1Auxiliary output 15 A protected
29AUX2Auxiliary output 25 A protected
30LINEAR_GND1TPS and MAP groundAnalogue ground
31NTC_1NTC sensor input 1Temperature sensor input
32TPS1Throttle position sensor 10–5 V input
33MAPManifold pressure sensor input0–5 V input
34VREF1TPS and MAP reference voltage5 V reference
35GROUNDPower ground—

23-way Tornado connector

PinNameFunctionSource notes
1IGN5/INJ7Ignition coil 5Power or TTL; hardware-selected
2IGN6/INJ8Ignition coil 6Power or TTL; hardware-selected
3AUX3Auxiliary output 3Configurable; 5 A protected
4AUX4Auxiliary output 4Configurable; 5 A protected
5HBRIDGE+DC motor positive5 A motor control
6HBRIDGE−DC motor negative5 A motor control
7FANS1Cooling fan relay 15 A protected
8FANS2Cooling fan relay 25 A protected
9PWM3PWM output 3Configurable; 5 A protected
10PWM4PWM output 45 A high-speed; shared with H-bridge
11WSPEED1Left rear wheel speedHall input
12WSPEED2Right rear wheel speedHall input
13WSPEED3Left front wheel speedHall input
14WSPEED4Right front wheel speedHall input
15LAMBDA2Lambda sensor bank 20–5 V input
16TPS2Analogue input0–5 V input
17PPS1Analogue input0–5 V input
18PPS2Analogue input0–5 V input
19LINEAR5Analogue input 50–5 V input
20NTC_2NTC sensor input 20–5 V temperature input
21NTC_3NTC sensor input 30–5 V temperature input
22SENS_GND2Analogue groundSensor ground
23VREF2Voltage reference5 V reference

13-way automotive harness expansion connector

The manual describes this as a connector usually provided on SC-supplied automotive looms; it is a harness connector, not the 23-way ECU connector. Individual looms can vary.

PinFunction
1+12 V ignition feed
2Ground
3Lambda sensor signal input
4Linear 1 analogue input
5Fuel pump output, positive supply to pump
6Relay 1 switched output
7PWM 1 output
8PWM 2 output
9Auxiliary 1 output
10Auxiliary 2 output
11Cam 2 input
12Reference voltage output
13Manifold pressure sensor input

Directly applicable articles

Technical articles assigned to this context will appear here.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.