
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan Patrol Y62 2017 onward VK56DD, with product code S7Plus-Nissan-Y62. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan Patrol Y62 2017 onward VK56DD installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Nissan Patrol Y62 2017 onward VK56DD product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU-to-loom schedules
From pages 4–6 of the Syvecs Nissan Patrol Y62 kit manual, version 1.0. The source identifies the kit as Y62 without restricting years in the connector chart: confirm the VK56DD application, hardware, connector orientation and loom revision with Syvecs. The table maps the three Syvecs ECU connectors to the manufacturer-listed Patrol loom positions and GDI12 driver where noted; it does not enumerate every factory cavity. A dash represents a blank in the source.
Connector A
| Syvecs pin | Description | Patrol loom / kit position | Manufacturer notes |
|---|---|---|---|
| A1 | PWR CTR OUT | 88 | Main relay |
| A2 | H-Bridge1 / SlaveOut1 | 108 | DBW+ |
| A3 | H-Bridge2 / SlaveOut2 | 107 | DBW− |
| A4 | H-Bridge3 / SlaveOut3 | 106 | Evap PWM |
| A5 | H-Bridge4 / SlaveOut4 | 90, 93 | VVEL trigger and fuel pump relay |
| A6 | H-Bridge5 / SlaveOut5 | — | — |
| A7 | H-Bridge6 / SlaveOut6 | External | External fan |
| A8 | H-Bridge7 / SlaveOut7 | 57 | Multiway + |
| A9 | H-Bridge8 / SlaveOut8 | 58 | Multiway − |
| A10 | FUEL1 | GDI12 pin 13 | Cylinder 1 injector |
| A11 | FUEL2 | GDI12 pin 22 | Cylinder 2 injector |
| A12 | FUEL3 | GDI12 pin 23 | Cylinder 3 injector |
| A13 | FUEL4 | GDI12 pin 19 | Cylinder 4 injector |
| A14 | FUEL5 | GDI12 pin 29 | Cylinder 5 injector |
| A15 | FUEL6 | GDI12 pin 14 | Cylinder 6 injector |
| A16 | FUEL7 | GDI12 pin 30 | Cylinder 7 injector |
| A17 | FUEL8 | GDI12 pin 17 | Cylinder 8 injector |
| A18 | PWM1 / FUEL9 | 126 | Tacho |
| A19 | PWM2 / FUEL10 | External | Secondary injector 1 |
| A20 | PWM3 / FUEL11 | 136 | Fuel pump computer |
| A21 | PWM4 / FUEL12 | External | Secondary injector 2 |
| A22 | PWM5 / FUEL13 | 114 | VVTi 1 EX — flyback solder bridge set |
| A23 | PWM6 / FUEL14 | 115 | VVTi 2 EX — flyback solder bridge set |
| A24 | PWM7 / FUEL15 | 112 | VVTi 1 — flyback solder bridge set |
| A25 | PWM8 / FUEL16 | 113 | VVTi 2 — flyback solder bridge set |
| A26 | IGN1 | 95 & 94 | Ignition 1 & 6 |
| A27 | IGN2 | 91 & 92 | Ignition 2 & 3 |
| A28 | IGN3 | 104 & 105 | Ignition 4 & 7 |
| A29 | IGN4 | 102 & 101 | Ignition 5 & 8 |
| A30 | IGN5 | 99 | Throttle control relay |
| A31 | IGN6 | GDI12 pin 21 | DI pump signal |
| A32 | PWRGND | — | — |
| A33 | PWRGND | 50 | ECU ground |
| A34 | PWRGND | 55 | ECU ground |
Connector B
| Syvecs pin | Description | Patrol loom / kit position | Manufacturer notes |
|---|---|---|---|
| B1 | PWRGND | 10 | Power ground |
| B2 | EGT2 + | 17 | EGT2 |
| B3 | EGT2 − | — | — |
| B4 | KNOCK | 15 | Knock sensor input |
| B5 | KNOCK 2 | 18 | Knock 2 |
| B6 | PVBAT | 120 | Constant 12 V |
| B7 | IVBAT | 145 | 12 V from ECM |
| B8 | LAM1A | 79 | 2.2 |
| B9 | LAM1B | 74 | 1.8 V varies |
| B10 | LAM1C | — | — |
| B11 | LAM1D | — | — |
| B12 | LAM1HEATER | 116 | Heater |
| B13 | IVBAT | 111 | 12 V from ECM |
| B14 | LAM2A | 69 | 2.2 |
| B15 | LAM2B | 70 | 1.8 V varies |
| B16 | LAM2C | — | — |
| B17 | LAM2D | — | — |
| B18 | LAM2HEATER | 117 | Heater |
| B19 | IVBAT | — | CAN bridge 12 V |
| B20 | KLINE | — | — |
| B21 | RS232RX / CAN L | — | — |
| B22 | RS232TX / CAN H | — | — |
| B23 | LANRX− | Orange/white | — |
| B24 | LANRX+ | White/orange | — |
| B25 | LANTX− | Green/white | — |
| B26 | LANTX+ | White/green | — |
Connector C
| Syvecs pin | Description | Patrol loom / kit position | Manufacturer notes |
|---|---|---|---|
| C1 | KNOCK GROUND | 20 | Knock ground |
| C2 | ANGND | 13, 42, 43, 44, 45 | Sensor ground |
| C3 | ANGND | 63, 85, 135, 144, 151 | Cam and crank ground |
| C4 | ANGND | — | Sensor ground |
| C5 | 5V OUT | 27, 28, 29, 30 | 5 V output for sensors |
| C6 | 5V OUT | 73, 83, 142, 146 | 5 V output for sensors |
| C7 | 5V OUT | — | 5 V output for sensors |
| C8 | CAN L | 123 | CAN L |
| C9 | CAN H | 124 | CAN H |
| C10 | AN01 | 31 | Cooling fan speed |
| C11 | AN02 | 41 | Cam 1 EX |
| C12 | AN03 | 68 | Cam 2 EX |
| C13 | AN04 | 25 | DI pressure |
| C14 | AN05 | 33 | Crank |
| C15 | AN06 | 40 | Cam 1 |
| C16 | AN07 | 66 | Cam 2 |
| C17 | AN08 | — | MAP |
| C18 | AN09 | 78 | TPS1A |
| C19 | AN10 | 80 | TPS1B |
| C20 | AN11 | 150 | PPSA |
| C21 | AN12 | 143 | PPSB |
| C22 | AN13 | 35 | Coolant temperature input |
| C23 | AN14 | 36 | Air temperature input |
| C24 | AN15 | 134 | Steering wheel switch |
| C25 | AN16 | 23 | Engine oil pressure |
| C26 | CAN3 L | 137 | — |
| C27 | CAN3 H | 138 | — |
| C28 | PWR CTR IN | 133 | Ignition switch |
| C29 | AN S1 / Slave An01 | Join to C24 | Steering wheel output buttons |
| C30 | AN S2 / Slave An02 | — | — |
| C31 | AN S3 / Slave An03 | 22 | Engine oil temperature |
| C32 | AN S4 / Slave An04 | 61 | Multiway position |
| C33 | AN S5 / Slave An05 | 12 | A/C pressure |
| C34 | AN S6 / Slave An06 | 128 | Fuel temperature |