
MaxxECU Chevrolet Corvette C6 (E38 ECM) plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Vehicle and ECU functions
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
| Options | OEM ECU PIN | MaxxECU IO | MaxxECU PRO | Note |
|---|---|---|---|---|
| 8 injection sequential | - | INJ 1-8 | YES | |
| 8 ignition sequential | - | IGN 1-8 | YES | |
| E-Throttle | B5/B6 | GPO 11, GPO 12 | Yes | |
| Camshaft solenoid | B16 | GPO 30 | Yes | Only on some models (Camaro SS (L99 with automatic transmission) |
| Evap canister purge solenoid | B8 | GPO 29 | Yes | |
| Evap canister vent solenoid | A61 | GPO 24 | Yes | |
| Fuel pump primary | A50 | GPO 15 (+12V) | YES | |
| Fuel pump secondary | A51 | GPO 16 (+12V) | YES | |
| Tachometer | A48 | GPO 8 | YES | |
| AC magnetic clutch | A63 | GPO 25 | Yes | |
| AC pressure signal | A12 | AIN 9 | YES | |
| Starter relay coil supply | A4 | DIN 5 | YES | |
| Low FAN | A58 | GPO 2 | YES | |
| High FAN | A17 | GPO 1 | YES | |
| Knock sensors (OEM) | B26, B29 | KNOCK1, KNOCK2 | YES | |
| Vehicle speed (individual wheel speed) | GM E38 ECM CAN | YES | ||
| Narrow band oxygen sensors | - | - | NO | Uses external (and included) Bosch LSU 4.2 wide band sensors |
| MAF (OEM) | A41 | AIN 17 | Yes | MAF should be removed. Use stock MAP sensor or use the MaxxECU built-in. |
| Service light/check engine light | A68 | GPO 26 | Yes | |
| Instrument cluster/ABS | GM E38 ECM CAN | Yes | ||
| Traction button | GM E38 ECM CAN | Yes | ||
| Fuel consumption | GM E38 ECM CAN | NO | ||
| Fuel level primary input | A16 | AIN 1 | YES | |
| Fuel level secondary input | A70 | AIN 2 | YES | |
| Brake switch signal | A9 | DIN 1 | YES | |
| ECT/CLT | B21 | CLT | YES | |
| Oil level switch | B33 | DIN 2 | YES | Only on early models |
| Oil pressure sensor | B50 | AIN 11 | YES | |
| Generator turn on signal | B61 | IGN 9 | YES | |
| Clutch position | A26 | AIN 18 | Yes* | Only available in REV2+ plugin adapters! |
| IAT (in OEM MAF) | A37 | IAT | YES | Also paralell connected with extra 2-pin GT150 connector (6) |
| Fuel tank pressure | A24 | AIN10 | YES | Not used for anything, but wired |
| Starter enable relay control | A52 | GPO 5 | YES | |
| Starter enable relay control | A67 | INJ 13 | YES | |
| VSS output to ABS system | A57 | GPO 7 | YES | |
| VSS high signal | A71 | IGN 12 | Yes | Experimental output |
| VSS low signal | A72 | IGN 10 | Yes | Experimental output |
| Generator field duty signal | B32 | - | NO | Not needed |
| MAP sensor (OEM) | B58 | AIN 12 | Yes | Used as MAP sensor input in default NA basetune, for forced induction, please use the built-in MAP sensor in MaxxECU |
| DME relay | A59 | GPO 23 | Yes | |
| Bluetooth ( MDash) | Yes | |||
| EGT option | Yes, 8 Directly | |||
| Cyl 6/7/10 shutoff valves | B9, B14, B10 | INJ 14/16/15 | Yes* | Only available in REV3 plugin adapters! |
| Cyl 4 shutoff / Reverse gear lockout solenoid | B11 | INJ 12 | Yes* | Only available in REV3 plugin adapters! |
| Fuel economy meter in dash | GM E38 ECM CAN | Yes | Needs to be manually calibrated, uses MaxxECU fuel consumption caluclation for output |
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
| Pin | Description | Usage | Note |
|---|---|---|---|
| 1 (H) | AIN 3 | 0-5V analog input | |
| 2 (G) | AIN 4 | 0-5V analog input | |
| 3 (F) | +12V | Output at ignition on | |
| 4 (E) | Engine GND | - | |
| 5 (D) | CAN 2 H | - | |
| 6 (C) | CAN 2 L | - | |
| 7 (B) | GPO 7/DIN 3 | Output or digital input | |
| 8 (A) | +5V sensor supply | - | |
| 9 (S) | INJ 9 | Output | |
| 10 (R) | INJ 10 | Output | |
| 11 (P) | INJ 11 | Output | |
| 12 (N) | Sensor GND | - | |
| 13 (M) | AIN 13 (0-5V) | 0-5V analog input | |
| 14 (L) | AIN 14 (0-5V) | 0-5V analog input | |
| 15 (K) | AIN 15 (0-5V) | 0-5V analog input | |
| 16 (J) | AIN 16 (0-5V) | 0-5V analog input |
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.
Documents
- MaxxECU Chevrolet Corvette C6 (E38 ECM) adapter installation and pinout
- GEN1 plug-in compatibility and wiring index
- MaxxECU manufacturer and universal-model index
Sources reviewed 17 November 2026.